Graco Horizon Fluid Management Systems Скачать руководство пользователя страница 9

Страница: 9 / 108

308607

Installation Checklist

System Startup

Installation Steps

Reference

13. Turn on the printer or computer.

14. Turn on the AC power to each control module. All the keypads should briefly

display a revision screen and then the HOME screen. The printer should print
“WELCOME TO HORIZON...” If the HOME screen is not displayed and/or
there is no print-out, see

Troubleshooting

, page 68.

Page 19

15. Using the Administrative Keypad, which is connected to the Master Control

Module, access the Setup screens. The Password is 1111 for a new system
installation.

Page 19

16.

If your system has one control module only,

disable the CAN network.

Page 21

17. Select CLEAR SETUP to initialize the system. Be sure to enter a new pass-

word for setup access before exiting Setup.

Page 23

18. Using the administrative keypad, connected to the Master Control Module,

complete the System Setup. Use the six forms that were filled out in the

Pre-installation Procedure

(refer to step 8, page 7) to enter the System

Map information into the Setup screens.

Pre-installation Forms
and Appendix, pages
86--95, or page 22,

New Setup Options

19. After entering all the setup data, reboot the system (turn the main power off

then on) to initialize the software.

Test the System

Installation Steps

Reference

20. Request a dispense job for each fluid to each location. If any problems occur,

see

Diagnostics

, page 26, and troubleshooting information on page 61.

Pages 48 -- 52

21. Select SETUP

PRINT SETUP

ALL MEMORY to print a record of all the

data entered during Setup. Send a copy of this record and all other required
documents as instructed in Pre-installation Form 6,

Warranty Registration &

Checkout Form

Pages 24 and 96

System Installation Complete

Содержание Horizon Fluid Management Systems













































































































Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды

Graco Horizon Fluid Management Systems, Инструкция по эксплуатации

Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды