Graco Horizon Fluid Management Systems Скачать руководство пользователя страница 55

Страница: 55 / 108

308607

Run Mode -- Report Jobs

Follow this procedure to retrieve reports on previously completed jobs.

This run option is only available on the Master Control Module.

Instructions

1. Select Report Jobs

NOTE:

REPORT JOBS can be initiated when jobs are

running, however, if a job completes and sends the

information to the printer or computer, the report will

be interrupted. It is best to run reports when no jobs

are running.

The system can hold up to 668 transactions before

it begins to write over the oldest jobs.

See page 40 for information about printer and

computer output. The report will be formatted as set

in COMM. on CM#1. See page 37.

a.. At the RUN screen, move the cursor to

REPORT JOBS by pressing the

key.

a. Press ENTER on the keypad.

Screens

RUN Screen

_ _ _ _ _ _ _ _ _ _

RUN

_ _ _ _ _ _ _ _ _ _

NEW JOB

VIEW CURRENT JOBS

REPORT JOBS

2. Report Jobs

a.. The REPORT JOBS screen appears with the

cursor in the DATE field.

b.. Type in the date you want the report to start

with.

c.. Press ENTER on the keypad. The cursor will

move to the TIME field.

d.. Type in the time you want the report to start

with. Note that the Horizon has a 24 hour

clock.

e.. Press ENTER on the keypad.

f.. The REPORT IN PROCESS screen will ap-

pear. Wait for the COMPLETED screen to

appear before pressing another key.

NOTE:

The length of time it takes to process

the report is dependant on how many jobs

were running in the requested report period

and whether the printer or computer is busy

processing other jobs.

If the system could not find jobs to report

within the time and date parameters called for,

the WARNING screen will appear.

a. After the COMPLETED screen appears, press

any key on the keypad to return to the RUN

screen.

REPORT JOBS Screen

RPT ALL JOBS SINCE

DATE (MMDDYY)

XXXXXX

TIME (HH:MM)

XX:XX

RPT ALL JOBS SINCE

DATE (MMDDYY)

XXXXXX

TIME (HH:MM)

XX:XX

REPORT IN PROCESS...

PLEASE WAIT

JOB REPORTS

SUCCESSFULLY

COMPLETED

USE ANY KEY TO CONT.

WARNING Screen

WARNING

NO JOB REPORTS FOUND

USE ANY KEY TO CONT.

Содержание Horizon Fluid Management Systems













































































































Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды

Graco Horizon Fluid Management Systems, Инструкция по эксплуатации

Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды