Graco Horizon Fluid Management Systems Скачать руководство пользователя страница 15

Страница: 15 / 108

308607

Cable Routing and Connection

7. Route the Solenoid and Meter Cables

to their Assigned Control Module

8. Connect the Solenoid and Meter

Cables

Connect the solenoid cables as shown in Fig.

6. The cables connect at the solenoid end with

wire nuts.

g. Connect the Ready Light as shown in Fig. 6.

h. Connect the pulse meter cables. The cables

connect at the pulse meter end with wire nuts.

Connect an oil meter as shown in Fig. 7.

Connect an anti-freeze meter as shown in

Fig. 8. Be sure to install the RC Filter.

Fig. 6

06577

P8 or P9

Solenoid Connection

Use bulk Cable P/N 113557 (500 ft. [152.5 m]) or 113558
(1000 ft. [305 m)]); 50 ft. (15.3 m) maximum length

Ready Light Kit 238996

NOTE:

If existing Ready Light is used, the bulb and lens must

be replaced with bulb P/N 113859 and lens 113857

Fluid Solenoid P/N 218588 (includes Ready Light), 215487 or
512927; Air Solenoid P/N 215407 or 512926

NOTE: See Fig. 9, page 16, for connector locations.

Fig. 7

06579

Pulse Meter P/N 238618 Connection

ground

signal

+12V

black

white

red

Connector J5 in this drawing; can be J5, J6, or J7

Use bulk Cable P/N 113555 (500 ft. [152.5 m]) or
113556 (1000 ft. [305 m)]); 50 ft. (15.3 m) maxi-

mum length

Pulse Meter P/N 238618

ground

signal

ground

+12V

shield

+12V

shield

black

white

red

Circuit Board

Fig. 8

06580

Pulse Meter P/N 215474 Connection

shield

black

red

Connector J5 in this drawing; can be J5, J6, or J7

RC Filter P/N 113837; included with meter

Pulse Meter P/N 215474

NC=No Connection

N/C

black

red

ground

signal

N/C

ground

signal

Содержание Horizon Fluid Management Systems













































































































Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды

Graco Horizon Fluid Management Systems, Инструкция по эксплуатации

Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды