Graco Horizon Fluid Management Systems Скачать руководство пользователя страница 11

Страница: 11 / 108

308607

Hardware Installation

3. Set Control Module Addresses and

Label the Boxes (continued)

DIP

Switch

No.

Address

Setting

OFF

Slave Control Modules are shipped with their address set

to 0.

4. To Change from 110 VAC to 220 VAC

WARNING

FIRE, EXPLOSION, AND ELECTRIC

SHOCK HAZARD

To reduce the risk of fire, explosion, and

electric shock all wiring must be done by

a qualified electrician.

a. Power should not be connected at this point of

installation if the procedure is being followed

properly. Make sure there is no power to the

control module(s).

b. See Fig. 2 wire connections for 110 VAC. Cut

the white wire connecting transformer termi-

nals 2 to 6 at the terminal 2 connector.

c. Cut the black wire connecting transformer

terminals 1 to 5 at the terminal 1 connector.

d. Switch the connectors on terminals 2 and 6.

See Fig. 2 wire connections for 220 VAC.

e. Strip 0.25 in. (6.4 mm) of insulation from the

wires connected to terminals 2 and 5. Connect

the wires together with a wire nut.

Содержание Horizon Fluid Management Systems













































































































Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды

Graco Horizon Fluid Management Systems, Инструкция по эксплуатации

Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды