Graco Horizon Fluid Management Systems Скачать руководство пользователя страница 6

Страница: 6 / 108

308607

Pre-installation Checklist

CAUTION

Accurately and thoroughly document the Control Module port connections and dispense areas. If the Software

Map does not exactly match the way the cables are connected, the system will not operate properly. Errors that

could occur include: inability to turn on a fluid at a given dispense area; the wrong fluid or dispense point is acti-

vated; or a fluid dispense point is properly activated, but the wrong meter is monitored so the dispense job will not

shut off properly.

This process is not difficult, but it is detailed and precise. Follow all steps and document them according to this

manual to ensure a successful installation.

NOTE:

Follow these steps before beginning to install the Horizon system.

Refer also to

Installation and Troubleshooting Tips

, beginning on page 61, for information that will help you

avoid installation problems and correct any problems that may occur.

Pre-installation Steps

Reference

1. Locate the Floor Plan, System Map (diagram of component locations), and all

other documentation used to specify the system prior to ordering it.

If this information cannot be located, recreate it from the packing slip that

came with the system.

Packing slip and
Appendix, pages
81--106

2. Verify that all the parts on the Floor Plan match the parts shipped to you.

Floor Plan, purchase
order, and packing
slip

3. Verify that all Horizon system components are marked in their proper loca-

tions on the Floor Plan.

Floor Plan

4. Assign a name and number to all the control modules in the system. Record

the control module numbers on the Floor Plan.

The Master Control Module (which the Administrative Keypad and printer

or computer connect to) is always assigned number 1.

Additional Slave Control Modules are numbered in sequence as 2, 3, etc.

The control modules do not have to be in numerical order along the

network cable.

Floor Plan

5. Assign a name and number to each dispense area. Record the names and

numbers on the Floor Plan.

The dispense area usually consists of banks of hose reels, but may also

consist of oil bars or individual hoses.

The names should make sense to the shop personnel who will use the

system. For example:

Fast Lube, Service Bay 3, etc

Floor Plan

6. Within each dispense area, verify that the Floor Plan shows the fluid that

each reel or hose should dispense.

Floor Plan

Содержание Horizon Fluid Management Systems













































































































Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды

Graco Horizon Fluid Management Systems, Инструкция по эксплуатации

Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды