Graco Horizon Fluid Management Systems Скачать руководство пользователя страница 36

Страница: 36 / 108

308607

System Setup -- Inventory

Instructions

Set Inventory Levels

If inventory tracking is disabled (default setting):

Can initiate any new jobs with preset or free flow.

Tank levels under INVNT menu will not count down.

Resettable/non-resettable totals will count up.

The tank level is not checked against the preset

amount.

Inventory alarms will not display in the HOME

screen.

If inventory tracking is enabled:

All system fluids must be tracked.

Tank levels under INVNT menu will count down.

Resettable/non-resettable totals will count up.

At the beginning of a job, the tank level is checked

against the preset amount. If the preset amount

exceeds the the amount of fluid in the tank, the job

will not start.

Inventory alarms will display on the last line of the

HOME screen on each keypad, as shown in the

Inventory Alarm Screen Display

example below.

Adding the fluid called for and updating the inven-

tory tank level will clear the alarm. See page 57.

To Enable Inventory Tracking:

1. Cursor is in the ENABLE/DISABLE field. DISABLE

is the default setting. Press the

key to scroll

to ENABLE.

2. Press ENTER to confirm the setting and go to the

next screen.

3. Cursor is in the fluid number (FL#01) field.
4. The fluid number will automatically increment up

by 1, based on the fluids entered while entering the

fluid data (page 32).

5. Press ENTER on the keypad.
6. Cursor moves to the REORDER PT. (point) field.
7. Type the minimum fluid level the tank should be

allowed to reach before receiving an alarm to refill

it.

8. Press ENTER on the keypad.
9. Cursor moves to the TANK LVL (level) field.
10. Type the current fluid level of the tank.
11. Press ENTER on the keypad.
12. When the cursor is at MORE, press ENTER to

repeat the screen for each fluid.

-- Or move the cursor to EXIT to exit the inventory

levels setup.

Screens

INVENTORY TRACKING:

DISABLE

ARROWS TO CHANGE

ENTER KEY TO COMMIT

FL#01

10W30

00010 GL REORDER PT.

00100.0 GL TANK LVL

EXIT

FL#01

10W30

00010 GL REORDER PT.

00100.0 GL TANK LVL

EXIT

FL#01

10W30

00010 GL REORDER PT.

00100.0 GL TANK LVL

EXIT

FL#01

10W30

00010 GL REORDER PT.

00100.0 GL TANK LVL

EXIT

Inventory Alarm Screen Display

_ _ _ _ _ _ _ _ _ _

HOME

_ _ _ _ _ _ _ _ _ _

RUN

SETUP

INVNT

LOW FL01

Содержание Horizon Fluid Management Systems













































































































Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды

Graco Horizon Fluid Management Systems, Инструкция по эксплуатации

Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды