Graco Horizon Fluid Management Systems Скачать руководство пользователя страница 72

Страница: 72 / 108

308607

Horizon System Components

Control Modules

Part No. 238624, Master Control Module

Part No. 238625, Slave Control Module

The Horizon system consists of a number of control

modules that are connected by cables to form a net-

work. The control modules provide the operating intelli-

gence for the system. There are two types of control

modules:

the

Master Control Module

and

the

Slave Control Module

Both types of control modules perform similar func-

tions. They drive air and fluid solenoids and count

pulses from meters. They have on-board memory that

contains a map of all available system resources and a

power supply that can be configured for either 110 or

220 VAC operation.

Master Control Module

The Master Control Module has several unique fea-

tures:

It has additional memory to hold data for completed

dispense jobs.

It controls activity over the CAN (Controller Area

Network), which is the network that interconnects

the control modules in a larger system.

It provides the printer and/or computer interface.

It continuously tracks the time and date.

Control Module Specifications:

There can be a total of 40 control modules in a

system, 1 Master plus 39 Slaves. There must be

only one Master Control Module per system. Any

additional control modules are Slave Control Mod-

ules.

Each control module (Master or Slave) can support

up to 6 solenoids, either air or fluid type.

Each Control Module can support up to 6 pulse

meters.

The Master Control Module requires the use of the

System Administrator Keypad to enter or change

setup information or to run diagnostics.

The control modules can be located any distance

apart, provided that the total length of cable from

one end of the network to the other end is no more

than 2000 ft. (610 m) long.

The Master Control Module can be located any-

where in the network, but because of its output port

(for printer or computer), it should be near the shop

office or printer/computer location.

Содержание Horizon Fluid Management Systems













































































































Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды

Graco Horizon Fluid Management Systems, Инструкция по эксплуатации

Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды