gefran AD Скачать руководство пользователя страница 66

Страница: 66 / 142

ADV200 WA • Quick start up guide - Specification and installation

T+

T-

LOC

ILim

n:0

Message

0 1

Load default

3
4

Press ESC to exit

Code: 0001H-1

1 MESSAGE

: identifies a message.

indicate show many messages are enqueued. The queue may contain a

maximum of 10 messages and the message with the highest number is the

most recent.

Description of the message (see

chapter 8

for further information)

Sub-code of the message. Provides extra information in addition to the descrip-

tion.

“Press ESC to exit” is displayed if the message requires acknowledgment.

When a message is closed, the next message is displayed until the queue is

empty.

Note !

For further information, see

chapter 8.2

6.8 Saving and recovery of new parameter settings

Drive parameters can be saved on the keypad in 5 different memory areas.

This function is useful to obtain various sets of parameters, for safety backup or to

transfer the parameters from one drive to another.

6.8.1 Selection of the keypad memory

T+

T-

LOC

ILim

n:0

0 4 . 1 9

PA R :

5 9 4

Keypad memory select

Def:

T+

T-

LOC

ILim

n:0

01 MONITOR

02 DRIVE INFO

03 STARTUP WIZARD

04 DRIVE CONFIG

T+

T-

LOC

ILim

n:0

0 4 . 1 9

PA R :

5 9 4

Keypad memory select

Def:

0 0 0 0 0 0 0 0 2

Menu 04 DRIVE CONFIG, parameter 04.21

Keypad memory select

, PAR : 594.

The keypad features 5 memory areas dedicated to saving parameters.

The memory to be used is selected using the

Keypad memory select

parameter.

Subsequent saving and recovery operations will be carried out on the memory

selected.

6.8.2 Saving of parameters on the keypad

T+

T-

LOC

ILim

n:0

0 4 . 1 7

PA R :

5 9 0

Save par to keypad

Press E to execute

T+

T-

LOC

ILim

n:0

0 4 . 1 7

PA R :

5 9 0

DRIVE --> K2006 X

T+

T-

LOC

ILim

n:0

01 MONITOR

02 DRIVE INFO

03 STARTUP WIZARD

04 DRIVE CONFIG

X 3

Menu 04 DRIVE CONFIG, parameter 04.19

Save par to keypad

, PAR : 590.

Is used to transfer the parameters from the drive to the selected keypad memory.

To start the operation, press the

key.

During transfer, a bar is displayed which indicates progress of the operation.

Instead of the letter

, the number of the currently selected keypad memory is

displayed.

At the end of transfer, if this has been completed successfully, the “Done” caption

is displayed for a few seconds with subsequent return to the initial page.

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды