gefran AD Скачать руководство пользователя страница 96

Страница: 96 / 142

ADV200 WA • Quick start up guide - Specification and installation

Index Error message shown

on the display

Sub-code

Description

Solution:

Ask Gefran for the correct key to enable the desired firmware function.

Param error

Condition

: if an error occurs during activation of the parameter database saved in flash; the alarm

is inserted in the alarm list and alarm log.

XXX0H-X

The code XXXXH-X indicates the IPA of the parameter that has been set outside the
range allowed when the database is enabled.

Solution

: Set the parameter causing the error to a value within the range and run

Save param-

eters

. Switch the drive off and then switch it back on again.

If the IPA of the parameter is not shown in the manual, contact the service centre.

Options cfg changed

Condition

: this may occur when powering the drive if an expansion card has been removed or

replaced or the incorrect enable key is inserted for a given firmware function.

0064H-100

Card removed from slot 1

0014H-20

Card removed from slot 2

0003H-3

Card removed from slot 3

0078H-120

Card removed from slot 1 and from slot 2

0067H-103

Card removed from slot 1 and from slot 3

0017H-23

Card removed from slot 2 and from slot 3

007BH-123

Card removed from slot 1, from slot 2 and from slot 3

Solution

: Check the hardware configuration, then press ESC. Save the parameters (

Save param-

eters

, menu 04.01 par 550) to save the new hardware configuration.

Note!

If any messages not included in this list are displayed, reference should be made to the manual of the
application used by the drive.

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды