gefran AD Скачать руководство пользователя страница 85

Страница: 85 / 142

ADV200 WA • Quick start up guide - Specification and installation

and/or from those of the expansion cards.

2 – Drive internal variables

Internal drive control system variables, from “function block” calculations, sent via

keypad, PC configurator or fieldbus.

Practical example

The following examples illustrate the philosophies and methods with which more

or less complex operations are performed in the single “function blocks”, the

results of which represent the output of the block.

• Example: Changing the Speed Reference source

The main drive reference (in the default configuration)

Ramp ref 1 mon

(PAR:

620) is generated by the output of the function block “

Ramp setpoint Block

”.

Its default source is the

Analog input 1 mon

signal (PAR: 1500), from the output

of the function block “

Analog input 1 Block

”, which in this case refers to analog

input 1 of the signal terminal strip.

To change the reference source from the analog input to a digital reference inside

the drive, the input signal must be changed to “

Ramp setpoint Block

”.

Enter the

Ramp ref 1 src

parameter (PAR: 610)

and set a new reference, select-

ing it from among those listed in the L_MLTREF selection list, for example

Dig

ramp ref 1

(PAR: 600).

• Example: Inverting the analog reference signal

To invert the “

Analog input 1 Block

” output signal, the value of the

An inp 1 sign

src

parameter (PAR: 1526), which has a default setting of

Null

(no operation),

must be changed by selecting the source of the command signal from among

those listed in the L_DIGSEL 2 selection list, for example

Digital input X mon

One

(function always enabled), etc.

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды