gefran AD Скачать руководство пользователя страница 86

Страница: 86 / 142

ADV200 WA • Quick start up guide - Specification and installation

-1

* -1

* +1

Analog input 1 mon

Analog input 1 Block

Ramp Setpoint Block

Null

Terminal input

Ramp ref 1 mon

Ramp ref 1 src

An inp 1 sign src

Null

An inp 1 alt value

An inp 1 alt sel src

Ramp ref invert src

The diagrams above illustrate the internal processing philosophy of the single

“function blocks” and the result of these changes on the other interconnected

“function blocks”.

Note !

This section contains a brief description of the functions of the other parameters in the function blocks
not included for the changes in the example.

The

An inp 1 alt sel src

parameter (PAR: 1528) can be used to select an alterna-

tive reference for the

Analog input 1 mon

(PAR: 1500) output.

The

An inp 1 alt value

parameter (PAR: 1524) determines the alternative refer-

ence value for the

Analog input 1 mon

(PAR: 1500) output.

The

Ramp ref invert src

parameter (PAR: 616) can be used to select the source

for the command to reverse the “

Ramp setpoint

” function block output.

The output signal from the “

Ramp setpoint

” block is displayed in the

Ramp ref 1

mon

parameter (PAR: 620).

7.3.4 Multiple destination

Several functions can be assigned together to each input: to display which and

how many functions have been assigned to each input, check the relative “

dest

”

parameter to see whether there is a number shown in square brackets to the right

of the number of the selected parameter (as shown in the figure below).

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды