gefran AD Скачать руководство пользователя страница 59

Страница: 59 / 142

ADV200 WA • Quick start up guide - Specification and installation

6 - Use of the keypad

This chapter describes the keypad and methods of use for display and program-

ming of inverter parameters.

6.1 Description

T+

T-

LOC ILim

n:0

01 MONITOR

02 DRIVE INFO
03 STARTUP WIZARD
04 DRIVE CONFIG

7 virtual leds line:

Four alphanumeric lines

with 21-digit each

led is lit

led is off

Membrane keyboard :

• commands

• navigation

LCD display

Membrane keyboard

Inverter control programming menu navigation keys.

Symbol

Reference

Description

Start

Starts the motor

Stop

Stops the motor

ESC

Escape

Returns to the higher level menu or submenu. Exit from a parameter, a list of parameters,

from the list of the last 10 parameters and from the

Goto

parameter function (see CUST).

Can be used to exit from a message that requires use of this.

FWD

REV

Forward/Reverse

Reverses the direction of rotation of the motor

LOC

REM

Local/Remote

Changes the method of use from local to remote and vice versa.

Is active only if the drive is not enabled.

RST

Reset

Resets alarms only if the causes have been eliminated.

CUST

Custom

The first time it is pressed, displays the list of the last 10 parameters modified.

Pressing this key a second time activates the Goto parameter function for access to a
parameter through its number. To exit these functions, press the

◄

key.

DISP

Display

Displays a list of drive functioning parameters.

Enter

Accesses the submenu or parameter selected or selects an operation,

Is used during parameter modification to confirm the new value set.

▲

Moves selection in a menu or a list of parameters up.

During modification of a parameter, increases the value of the digit under the cursor.

▼

Down

Moves the selection in a menu or a list of parameters down.

During modification of a parameter, decreases the value of the digit under the cursor.

◄

Left

Returns to the higher level menu.

During modification of a parameter, moves the cursor to the left.

►

Right

Accesses the submenu or parameter selected.

During modification of a parameter, moves the cursor to the right.

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды