gefran AD Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 142

background image

88

ADV200 WA • Quick start up guide - Specification and installation

8 - Troubleshooting

8.1 Alarms

Note !

To reset alarms, see

paragraph 6.6.1

.

In the following table, the Code is visible only from serial line.

Code

Error message shown

on the display

Sub-code

Description

0

No alarm

Condition:

No alarm present

1

Overvoltage

Condition: DC link overvoltage alarm due to energy recovered from the motor.

The voltage arriving at the drive power section is too high compared to the maximum threshold
relating to the PAR 560

Mains voltage

parameter setting.

Solution:

- Extend the deceleration ramp.
- Use a braking resistor between terminals BR1 and BR2 to dissipate the recovered energy
- Use the VDC Control function

2

Undervoltage

Condition:

DC link undervoltage alarm.

The voltage arriving at the drive power section is too low compared to the minimum threshold
relating to the 560 Mains voltage parameter setting due to:.
- the mains voltage being too low or overextended voltage drops.
- poor cable connections (e.g. loose contactor terminals, inductance, filter, etc. ).

Solution:

Check the connections.

3

Ground fault

Condition:

Ground short circuit alarm

Solution:

- Check drive and motor wiring.
- Check that the motor is not grounded.

4

Overcurrent

Condition: Instantaneous overcurrent protection intervention alarm.

This may be due to the incorrect setting of current regulator parameters or a short circuit
between phases or ground fault on the drive output.

Solution:

- Check the current regulator parameters
- Check wiring towards the motor

5

Desaturation

Condition: Instantaneous overcurrent in the IGBT bridge alarm.
Solution:

Switch the drive off and then switch it on again.

If the alarm persists, contact the technical service centre.

6

MultiUndervolt

Condition:

The number of attempted automatic restarts after the

Undervoltage

alarm has

exceeded the set

PAR 4650 UVRep attempts

value in the

PAR 4652 UVRep delay

time.

Solution:

Too many Undervoltage alarms.

Adopt the proposed solutions for the Undervoltage alarm.

7

MultiOvercurr

Condition:

2 attempted automatic restarts after the Overcurrent alarm within 30 seconds. If

more than 30 seconds pass after the Overcurrent alarm was generated, the attempt counter is
reset.

Solution:

Too many Overcurrent alarms. Adopt the proposed solutions for the Overcurrent

alarm.

8

MultiDesat

Condition:

2 attempted at automatic restarts after the Desaturation alarm within 30 seconds.

If more than 30 seconds pass after the Desaturation alarm was generated, the attempt counter
is reset.

Solution:

Too many

Desaturation

alarms.

Adopt the proposed solutions for the

Desaturation

alarm.

«
...
86
87
88
89
90
...
»

Содержание AD















































































































































Отзывы:

Нет отзывов

Похожие инструкции для AD

Бренд: ECG Страницы: 15

Бренд: IBM Страницы: 54

MILLENIUM 1100-46D

Бренд: York Страницы: 24

Бренд: HP Страницы: 2

Бренд: Sony Страницы: 40

ILBLP CP10 HE SD

Бренд: IOTA Страницы: 8

DRIVE SHAFT-50PRO

Бренд: DoorHan Страницы: 18

Бренд: RIB Страницы: 56

Бренд: YASKAWA Страницы: 145

Бренд: YASKAWA Страницы: 320

RangeMaster V Series

Бренд: HardWay Страницы: 8

Бренд: Melec Страницы: 46

Бренд: EACON Страницы: 32

SERVOSTAR CD-LITE

Бренд: Danaher Motion Страницы: 49

Бренд: Vari Страницы: 30

Бренд: Fastech Страницы: 60

Бренд: Acclaim Lighting Страницы: 24

Бренд: Samsung Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды