gefran AD Скачать руководство пользователя страница 132

Страница: 132 / 142

132

ADV200 WA • Quick start up guide - Specification and installation

Appendix 1 - Parallel connection (500 ... 1200kW sizes)

A 1.1 Introduction

To obtain a drive of more than 400 kW connect a number of single units of be-

tween 250 kW and 400 kW in parallel.

A parallel connection of several drives basically consists of one MASTER unit and

one or more SLAVE units.

Power

code

Description (Designation)

code

Description (Designation)

500kW

S9O25WM

ADV200-WA-72500-KXX-4-MS 05 -SI

S9O25WMC

ADV200-WA-72500-KXX-4- MS 05-DC- SI

S9O25WS

ADV200-WA-72500-XXX-4-SL

S9O25SWMC ADV200-WA-72500-KXX-4- SL-DC

630kW

S9O26WM

ADV200-WA-73150-KXX-4-MS 06 -SI

S9O26WMC

ADV200-WA-73150-KXX-4-MS 06-DC-SI

S9O26WS

ADV200-WA-73150-XXX-4-SL

S9O26WSC

ADV200-WA-73150-KXX-4-SL-DC

710kW

S9O27WM

ADV200-WA-73550-KXX-4-MS 07 -SI

S9O27WMC

ADV200-WA-73550-KXX-4-MS 07-DC-SI

S9O27WS

ADV200-WA-73550-XXX-4-SL

S9O27WSC

ADV200-WA-73550-KXX-4-SL-DC

800kW

S9O28WM

ADV200-WA-74000-KXX-4-MS 08 -SI

S9O28WMC

ADV200-WA-74000-KXX-4- MS 08-DC-SI

S9O28WS

ADV200-WA-74000-XXX-4-SL

S9O28WSC

ADV200-WA-74000-KXX-4- SL-DC

1000kW

S9O27WM1 ADV200-WA-73550-KXX-4-MS 10 -SI

S9O27WM2

ADV200-WA-73550-KXX-4-MS 10-DC-SI

S9O27WS

ADV200-WA-73550-XXX-4-SL

S9O27WSC

ADV200-WA-73550-KXX-4-SL-DC

S9O27WS

ADV200-WA-73550-XXX-4-SL

S9O27WSC

ADV200-WA-73550-KXX-4-SL-DC

1200kW

S9O28WM1 ADV200-WA-74000-KXX-4-MS 12 -SI

S9O28WM2

ADV200-WA-74000-KXX-4- MS 12-DC-SI

S9O28WS

ADV200-WA-74000-XXX-4-SL

S9O28WSC

ADV200-WA-74000-KXX-4- SL-DC

S9O28WS

ADV200-WA-74000-XXX-4-SL

S9O28WSC

ADV200-WA-74000-KXX-4- SL-DC

710kW

S9O29WM

ADV200-WA-73550-KXX-4A-MS 07-SI

S9O29WMC

ADV200-WA-73550-KXX-4A-MS 07-DC-SI

S9O29WS

ADV200-WA-73550-KXX-4A -SL

S9O29WSC

ADV200-WA-73550-KXX-4A -SL-DC

800kW

S9O30WM

ADV200-WA-74000-KXX-4A- MS 08-SI

S9O30WMC

ADV200-WA-74000-KXX-4A- MS 08-DC-SI

S9O30WS

ADV200-WA-74000-KXX-4A- SL

S9O30WSC

ADV200-WA-74000-KXX-4A- SL-DC

1000kW

S9O29WM1 ADV200-WA-73550-KXX-4A-MS 10-SI

S9O29WM2

ADV200-WA-73550-KXX-4A-MS 10-DC-SI

S9O29WS

ADV200-WA-73550-KXX-4A -SL

S9O29WSC

ADV200-WA-73550-KXX-4A -SL-DC

S9O29WS

ADV200-WA-73550-KXX-4A -SL

S9O29WSC

ADV200-WA-73550-KXX-4A -SL-DC

1200kW

S9O30WM1 ADV200-WA-74000-KXX-4A- MS 12-SI

S9O30WM2

ADV200-WA-74000-KXX-4A- MS 12-DC-SI

S9O30WS

ADV200-WA-74000-KXX-4A- SL

S9O30WSC

ADV200-WA-74000-KXX-4A- SL-DC

S9O30WS

ADV200-WA-74000-KXX-4A- SL

S9O30WSC

ADV200-WA-74000-KXX-4A- SL-DC

Master unit

this is the only one to have the regulation card and keypad. It differs from the

standard single unit in that the power section control card (INT-P-ADV) is recon-

figured to function as MASTER and includes one or more MASTER - SLAVE (INT-

SLAVE) interface cards, one card for each slave that is connected.

The MASTER - SLAVE interface is achieved via a specific signal cable included in

the SLAVE drive packaging.

Slave unit

It differs from the standard single unit in that it has a dedicated power section

control card (INT-P-ADV) and there is no regulation card or keypad.

INT-P-ADV-MASTER card

The INT-P-ADV-MASTER card provided with one or more INT-SLAVE cards, acts

as the interface between the R-ADV regulation card and the power section of the

master unit and all the slave units. It also performs the following functions:

•

current signal scaling (via dip switch, factory-set)

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды