gefran AD Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 142

background image

ADV200 WA • Quick start up guide - Specification and installation

93

Index Error message shown

on the display

Sub-code

Description

4

Error in motor connection.

Solution

:Check the motor connection, set the value of the direct current of the

motor to 1/3 and perform the motor autotune procedure. Then increase the direct
current until autotuning is executed. The penultimate value is the nominal current
value at which the drive performs autotuning.

5

While running self-tuning the ESC key was pressed or the enable contact was
opened or an alarm occurred. The

Autotune

command was sent with the drive in

the alarm condition

Solution

: Eliminate the reason for the alarm, remove the reason for the opening of

the enable contact, reset alarms.

6

A setting performed by the

Autotune

function produced a parameter value outside

the min or max range.

Solution

: Check the motor plate data or drive and motor sizes have been combined

incorrectly.

7

The

Autotune

command was sent without being enabled.

Solution

: Close the enable contact before sending the

Autotune

command

8

Internal calculation error concerning IGBT control

Solution

: Perform autotuning once more, if the problem persists, contact the Gefran

technical support centre.

9

The drive has measured a stator resistance value exceeding the set limit.

Solution

: contact the Gefran technical support centre.

10

The drive has measured a stator resistance value below the set limit.

Solution

: contact the Gefran technical support centre.

11-12

Measurement of DTL internal compensation voltage outside accepted range.

Solution

: check connection between drive and motor.

If correct, the drive is faulty, contact the Gefran technical support centre.

13-14

Measurement of DTS internal voltage outside accepted range.

Solution

: check connection between drive and motor.

If correct, the drive is faulty, contact the Gefran technical support centre.

15 - 16 -17

LS leakage inductance value outside accepted range.

Solution

: Perform autotuning once more, if the problem persists, contact the Gefran

technical support centre.

18-19

Measurement of Im magnetising current outside accepted range.

Solution

: Perform autotuning once more, if the problem persists, contact the Gefran

technical support centre.

20-21

Measurement of Rr rotor resistor outside accepted range.

Solution

: Perform autotuning once more, if the problem persists, contact the Gefran

technical support centre.

Solution:

If the message appears with a value other than 0, follow the instructions supplied for

each particular case and repeat

Autotune

. This should be performed using the wizard function

available from the keypad (STARTUP WIZARD) and the Tool software on the PC.
Pay attention to all motor plate data parmaeters, especially:
-

Rated speed

,

Motor rated speed

in rpm.

-

Rated frequency

,

Motor rated frequency

in Hz

-

Pole pairs

,

Motor pole pairs

Take care not to set the

Rated speed

parameter to the synchronous speed. The value of the

Rated

speed

parameter must be less than: [(

Rated frequency

* 60) /

Pole pairs

].

If the problem persists even after following the instructions supplied, confirm the values of the mo-
tor plate data parameters, execute the

Take parameters

command but not

Autotune

.

«
...
91
92
93
94
95
...
»

Содержание AD















































































































































Отзывы:

Нет отзывов

Похожие инструкции для AD

Бренд: National Instruments Страницы: 30

Бренд: JMC Страницы: 28

Бренд: Lenze Страницы: 210

Artemis Servotorq II

Бренд: Overview Страницы: 2

Бренд: BeiJer Страницы: 84

Бренд: TECO-Westinghouse Страницы: 459

ACTIVE CUBE Series

Бренд: BONFIGLIOLI Vectron Страницы: 200

CoolDrive Series

Бренд: Tsino Dynatron Страницы: 285

Бренд: MSI Страницы: 2

Бренд: AMX Страницы: 2

Бренд: Teac Страницы: 1

Бренд: LinMot Страницы: 24

Бренд: Insignia Страницы: 92

Allen-Bradley PowerFlex 20-750-EMC2-F5

Бренд: Rockwell Automation Страницы: 20

Бренд: Lin Engineering Страницы: 29

Бренд: IBM Страницы: 50

OPTIONS P09N4108

Бренд: IBM Страницы: 34

Бренд: WAREMA Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды