gefran AD Скачать руководство пользователя страница 81

Страница: 81 / 142

ADV200 WA • Quick start up guide - Specification and installation

894) to use the internal motor potentiometer of the drive. If sending the com-

mand from the operator keypad, to use the motor potentiometer function enter

the

Mpot setpoint

parameter (PAR: 870) modify mode and press the Up (▲)

and Down (▼) keys.

Jog output mon

parameter (09 - JOG FUNCTION menu, PAR: 920) to use

one of the drive’s internal jog speeds.

Signals from expansion cards, the serial line or fieldbus can also be set as speed

references (see the detailed description of parameters).

• Setting the type of analog reference

If the analog input has been selected, choose the type of signal to use in the

Ana-

log inp 1 type

parameter (14 - ANALOG INPUTS menu, PAR.1502):

± 10V

0-20mA o 0-10V

4-20mA

As well as programming the

Analog inp 1 type

parameter (PAR:1502) you must

also verify the position of the switches on the regulation card, as showed on

chapter 5.2.4.

• Ramps setting

The acceleration and deceleration ramps can be set in

Acceleration time 0

(06 -

RAMPS menu, PAR: 700) and

Deceleration time 0

(PAR: 702).

The signal available on the analog input can be adjusted using

Analog inp 1

scale

parameter (14 - ANALOG INPUTS menu, PAR: 1504),

An inp 1 offset

tune

parameter (PAR: 1506) and

An inp 1 gain tune

parameter (PAR: 1508).

To use a digital speed to control the drive, enter it in the

Dig ramp ref 1

parameter

(05 - REFERENCES menu, PAR: 600).
The ramps are the same used with the reference signal from the analog input.

• Multispeed

To use more than one digital speed, use the multi-speed function.
First select the source of the speed signals

Multi ref 0 src

and

Multi ref 1 src

(07

- MULTI REFERENCE menu, PAR: 832 e 834) from the L_MLTREF selection list.
Next define which digital inputs are to perform switching between the various

speeds; use the

Multi ref sel .. src

parameters (PAR: from 840 to 846) to select

the signals to use from the L_DIGSEL2 selection list. Set the desired speeds in

the

Multi reference 0...7

parameters (PAR: from 800 to 814).

Also in this case the ramps can be set in the

Acceleration time 0

parameter

(06 - RAMPS menu, PAR: 700) and

Deceleration time

parameter (PAR: 702)

parameters.

• Motor potentiometer

To use the motor potentiometer, the signals to increase or decrease the reference

must be defined: set the

Mpot up src

parameter (08 - MOTOPOTENTIOMETER

menu, PAR: 884) and

Mpot down src

parameter (PAR: 886) parameters respec-

tively to increase and decrease the reference using selection list L_DIGSEL2.

Set the motor potentiometer ramps using

Mpot acceleration

(PAR: 872) and

Mpot deceleration

parameters (PAR: 874).

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды