gefran AD Скачать руководство пользователя страница 79

Страница: 79 / 142

ADV200 WA • Quick start up guide - Specification and installation

Step 8 - Setting the motor in “Flux Vect OL” mode (sensorless)

Menu 04 DRIVE CONFIG, parameter 04.2

Regulation mode

, PAR: 552,

set = [1] Flux vector OL.

Test with no load applied to the motor

1 Set the value of PAR 2308

OverFlux perc

to 120%.

2. Set the value of PAR 2312

OverFlux spd thr

to approximately 25% of the

rated speed.

3. Close the

Enable

contact (terminals S3 – 7).

4. Close the

FR forward src contact

(PAR 1042), terminals S3 – 8. The drive

starts magnetising the motor.

5. Using the potentiometer, gradually increase the reference signal until reaching

the maximum speed.

6. Open the

FR forward src contact

(PAR 1042), terminals S3 – 8, until reach-

ing the minimum set speed requested by the application.

7. Check that the ramp is linear and, once the set value has been reached, that

the minimum speed remains stable.

If the ramp is not linear and the minimum speed is not stable, reduce the value

of PAR 2306

Flux observe gain OL

in steps of 5.

Examples of values for PAR 2306 with standard 4-pole motors

100

For motor power ratings up to 15 kW

40-50

For motor power ratings of 45-55 kW

20-30

For motor power ratings of more than 132 kW

8. To save the new parameter settings, so that they are maintained also after

power-off, proceed as follows:

T+

T-

LOC

ILim

n:0

0 4 . 0 1

PA R :

5 5 0

Save arameters

Press E to execute

T+

T-

LOC

ILim

n:0

01 MONITOR

02 DRIVE INFO

03 STARTUP WIZARD

04 DRIVE CONFIG

T+

T-

LOC

ILim

n:0

0 4 . 0 1

PA R :

5 5 0

Save arameters

In ro ress

T+

T-

LOC

ILim

n:0

0 4 . 0 1

PA R :

5 5 0

Save arameters

Done

Test with rated load applied to the motor

1. Close the

Enable

contact (terminals S3 – 7).

2. Close the

FR forward src

contact (PAR 1042), terminals S3 – 8. The drive

starts magnetising the motor.

3. Using the potentiometer, gradually increase the reference signal until reaching

the maximum speed.

4. Open the

FR forward src contact

(PAR 1042), terminals S3 – 8, until reach-

ing the minimum set speed requested by the application.

- if current overload conditions occur at the minimum speed,

- if the current exceeds the rated current value setting,

- if the motor shaft is blocked at zero speed,

reduce the value set in PAR 2306

Flux observe gain OL

in steps of 5 until

reaching the best working condition with no overload.

5. To save, repeat step 6.

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды