gefran AD Скачать руководство пользователя страница 14

Страница: 14 / 142

ADV200 WA • Quick start up guide - Specification and installation

The inverter must be selected according to the rated current of the motor.

The rated output current of the drive must be higher than or equal to the rated cur-

rent of the motor used.

The speed of the three-phase motor is determined by the number of pole pairs and

the frequency (nameplate, data sheet) of the motor concerned.

Operation above the rated frequency and speed of the motor must take into ac-

count the specifications given by the manufacturer losses (bearings, unbalance

etc.). This also applies to temperature specifications for continuous operation under

20 Hz (poor motor ventilation, not applicable to motors with external ventilation).

2.1.1 Parallel inverters

•

Inverters of between 500 kW and 800 kW comprise one master and one

slave.

•

Inverters of over 1000 kW comprise one master and two slaves.

When placing your order

please give the code number of the master and slave

and number of these

Power

code

Description (Designation)

code

Description (Designation)

500kW

S9O25WM

ADV200-WA-72500-KXX-4-MS 05 -SI

S9O25WMC

ADV200-WA-72500-KXX-4- MS 05-DC- SI

S9O25WS

ADV200-WA-72500-XXX-4-SL

S9O25SWMC ADV200-WA-72500-KXX-4- SL-DC

630kW

S9O26WM

ADV200-WA-73150-KXX-4-MS 06 -SI

S9O26WMC

ADV200-WA-73150-KXX-4-MS 06-DC-SI

S9O26WS

ADV200-WA-73150-XXX-4-SL

S9O26WSC

ADV200-WA-73150-KXX-4-SL-DC

710kW

S9O27WM

ADV200-WA-73550-KXX-4-MS 07 -SI

S9O27WMC

ADV200-WA-73550-KXX-4-MS 07-DC-SI

S9O27WS

ADV200-WA-73550-XXX-4-SL

S9O27WSC

ADV200-WA-73550-KXX-4-SL-DC

800kW

S9O28WM

ADV200-WA-74000-KXX-4-MS 08 -SI

S9O28WMC

ADV200-WA-74000-KXX-4- MS 08-DC-SI

S9O28WS

ADV200-WA-74000-XXX-4-SL

S9O28WSC

ADV200-WA-74000-KXX-4- SL-DC

1000kW

S9O27WM1 ADV200-WA-73550-KXX-4-MS 10 -SI

S9O27WM2

ADV200-WA-73550-KXX-4-MS 10-DC-SI

S9O27WS

ADV200-WA-73550-XXX-4-SL

S9O27WSC

ADV200-WA-73550-KXX-4-SL-DC

S9O27WS

ADV200-WA-73550-XXX-4-SL

S9O27WSC

ADV200-WA-73550-KXX-4-SL-DC

1200kW

S9O28WM1 ADV200-WA-74000-KXX-4-MS 12 -SI

S9O28WM2

ADV200-WA-74000-KXX-4- MS 12-DC-SI

S9O28WS

ADV200-WA-74000-XXX-4-SL

S9O28WSC

ADV200-WA-74000-KXX-4- SL-DC

S9O28WS

ADV200-WA-74000-XXX-4-SL

S9O28WSC

ADV200-WA-74000-KXX-4- SL-DC

710kW

S9O29WM

ADV200-WA-73550-KXX-4A-MS 07-SI

S9O29WMC

ADV200-WA-73550-KXX-4A-MS 07-DC-SI

S9O29WS

ADV200-WA-73550-KXX-4A -SL

S9O29WSC

ADV200-WA-73550-KXX-4A -SL-DC

800kW

S9O30WM

ADV200-WA-74000-KXX-4A- MS 08-SI

S9O30WMC

ADV200-WA-74000-KXX-4A- MS 08-DC-SI

S9O30WS

ADV200-WA-74000-KXX-4A- SL

S9O30WSC

ADV200-WA-74000-KXX-4A- SL-DC

1000kW

S9O29WM1 ADV200-WA-73550-KXX-4A-MS 10-SI

S9O29WM2

ADV200-WA-73550-KXX-4A-MS 10-DC-SI

S9O29WS

ADV200-WA-73550-KXX-4A -SL

S9O29WSC

ADV200-WA-73550-KXX-4A -SL-DC

S9O29WS

ADV200-WA-73550-KXX-4A -SL

S9O29WSC

ADV200-WA-73550-KXX-4A -SL-DC

1200kW

S9O30WM1 ADV200-WA-74000-KXX-4A- MS 12-SI

S9O30WM2

ADV200-WA-74000-KXX-4A- MS 12-DC-SI

S9O30WS

ADV200-WA-74000-KXX-4A- SL

S9O30WSC

ADV200-WA-74000-KXX-4A- SL-DC

S9O30WS

ADV200-WA-74000-KXX-4A- SL

S9O30WSC

ADV200-WA-74000-KXX-4A- SL-DC

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды