GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 240

background image

Hardware installation

59

2062973-002

4.

Press the battery door closed until it seals the battery compartment.

6.2 Mounting the patient monitor

The patient monitor has an integrated GCX mounting plate. This facilitates all mounting options
for the patient monitor. Refer to the CARESCAPE Modular Monitors Mounting Solutions to
identify the compatible mounting hardware for the patient monitor.

Install the patient monitor to the mounting hardware according to the installation instructions
included with the mounting hardware.

WARNING

Never install equipment above the patient.

WARNING

Use only manufacturer specified mounts.

WARNING

To prevent liquids from entering the monitor, do not tilt the monitor more
than +/-15 degrees.

CAUTION

The device/system should not be used adjacent to, or stacked with, other

equipment. Consult qualified personnel regarding device/system configuration.

«
...
65
66
67
68
69
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B650

Бренд: GE Страницы: 242

Бренд: GE Страницы: 24

Бренд: Balanced Body Страницы: 3

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: RayLight Страницы: 34

GAZELLE FREESTYLE

Бренд: Gazelle Страницы: 10

Бренд: Latham Страницы: 19

Бренд: TEC Страницы: 6

Бренд: U Technology Страницы: 6

Бренд: Wasp Страницы: 50

Бренд: KCI Страницы: 2

Бренд: KCI Страницы: 60

Бренд: Landoll Страницы: 38

Бренд: Dantel Страницы: 22

Бренд: RAMVAC Страницы: 53

Бренд: Magicfx Страницы: 25

Бренд: Valmont Structures Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды