GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 199

Страница: 199 / 240

Disassembly and reassembly

191

2062973-002

12.3.5 Disassembling the main unit into Rear and Front units

Disassemble first:
a.

12.3.2. Detaching the Interface Board

12.3.3. Detaching the Frame Side Housing Decorations

12.3.4. Detaching the Top Cover

1. Set the monitor lying on its back and remove

the two screws (T10) from the bottom.

[Torque 0.8 m]

- NOTE: Be careful not to break the PDM

docking mechanism. Consider detaching it
according to section

12.2.3

2. Set the rear side of the Main Unit facing you.
3. Remove the three T10 screws from the left

side. [Torque 0.8 Nm]

4. Remove the two T10 screws from the right

side next to the Module Frame hinges. [Torque
0.8 Nm].

5. Detach the Module Frame back plate and

disconnect the Hinge Flex Board from the
Module Frame connectors,

see section

12.2.5

NOTE: Handle the Hinge Flex Board with care
when disconnected. Do not twist it or bend it
down.
6. Carefully lead the Hinge Flex Board through

the opening, and turn the Module Frame
against the main unit.

Содержание CARESCAPE Monitor B650

















































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B650

Отзывы:

Похожие инструкции для CARESCAPE Monitor B650

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B650, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B650

Отзывы:

Похожие инструкции для CARESCAPE Monitor B650

Бренды по названию

Популярные бренды