manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B650, Техническое руководство

Поделиться
Скачать
GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 145

 Maintenance and checkout

  137

2062973-002

10.4.4 Charging a battery

The battery is charged whenever it is installed into the patient monitor and the patient monitor 
is connected to an AC power source. The battery is charging both when the patient monitor is 
turned on and when it is in the standby mode. 
Battery is charging as long as the orange battery charging LED indicator is lit.
To check the battery charge status, select 

Monitor Setup > Battery Status > Advanced

.

10.4.5 Conditioning a battery

Condition the battery when a 

Condition monitor battery

 message is shown on the monitor 

screen. The condition cycle recalibrates the electronic fuel gauge.
Condition the battery by fully discharging and recharging the battery twice according to the 
following procedure:
NOTE: The patient monitor must be in a discharged state during battery conditioning. 
Disconnect any acquisition modules from the patient monitor if connected.
1.

Turn on the patient monitor. Disconnect the power cord from the wall outlet. Leave the 
patient monitor on until the battery is fully discharged and the patient monitor turns off 
automatically. 

NOTE: Ignore the 

Monitor Battery Low

 and 

Monitor Battery Empty!

 messages when 

discharging the battery.
2.

Reconnect the power cord to the wall outlet and turn on the patient monitor. Leave the 
patient monitor on until the battery is fully recharged and the orange battery charging 
indicator LED turns off.

3.

Repeat the steps 1 and 2 once.

The battery is now conditioned and ready for use. However if the 

Condition monitor battery 

message is still shown on the patient monitor screen, repeat the conditioning cycle once more. 
If the problem persists, replace the battery.
NOTE: Refer to section 

11.6. Battery diagnostics

 and 

11.7. Error messages and codes

 for more 

detailed information about the battery status and operating condition.

10.4.6 Replacing a battery

Replace the battery in the following situations:

−

if the 

Replace monitor battery

 message is displayed. This message indicates that the full-

charge capacity of the used battery has considerably degraded compared to the design 
capacity of a new battery.

−

if the 

Battery failure

 message is displayed.

Remove the battery from the patient monitor and install a new battery according to the battery 
installation instructions in the Hardware Installation section
NOTE: Refer to the section 

11.6. Battery diagnostics

 and 

11.7. Error messages and codes

 for 

more detailed information about the battery status and operating condition.
NOTE: Refer to the Troubleshooting chapter for more detailed information about the battery 
diagnostics and error messages.

WARNING

Do not incinerate a battery or store at high temperatures. Serious injury or 
death could result.

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды