GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 240

background image

CARESCAPE Monitor B650

144

2062973-002

The Hardware Statistics module displays several internal voltages, temperatures and power
consumption. A value is displayed in red, if the current reading exceeds a pre-determined lower
or upper limit, A value is displayed either as “0” or as “--”, if it cannot be measured.
To access hardware statistics:
1.

Log in to Webmin.

2.

Select

Diagnostics > Hardware Stats

.

3.

Scroll down the page to view the following device information:

The controlled parameters are measured with A/D converters and temperature sensors in the
specified subsystem. The measured values are then communicated over the I2C bus to the
power management controller in the DC/DC board for processing, except for CPU voltages,
which are both measured and processed by the CPU board.

Measurement

Description

+ 1.5V CPU Core Voltage (in mV)

+ 1.8V CPU Core Voltage (in mV)

+ 2.5V CPU Core Voltage (in mV)

These CPU core voltages are generated on the CPU
board from the +3.3 V supplied by the DC/DC board.

+ 12 Vsync CPU Voltage (in mV)

- 12 Vsync CPU Voltage (in mV)

These voltages are generated for the ECG and Invasive
pressure analog outputs and marker-out
synchronization pulse. The voltages are measured from
the CPU board.

AC/DC voltage (mV)

The AC/DC voltage is generated by the AC/DC power
supply unit and supplied as an input voltage to the DC/
DC board. The voltage is measured from the DC/DC
board. The AC/DC voltage is “0”, if the patient monitor is
not connected to the AC mains.

Also see section

11.4. Power management LEDs

.

VSYS voltage (mV)

+15V MOD voltage (mV)

+12V voltage (mV)

+5V voltage (mV)

+3.3V voltage (mV)

These voltages are generated by the DC/DC board and
they are routed via the CPU board to supply power to
other internal subsystems. The + 12 V is also supplied
directly to the backlight LED adapter boardLED backlight
of the LCD display. The +15VMOD voltage is “0”, if E-
module interface board is not installed. VSYS, +12V, +5V
and +3.3V voltages are measured from the DC/DC
board. +15VMOD is measured from the E-module
interface board.

Also see section

11.4. Power management LEDs

.

+5V REC voltage (mV)

+12V REC voltage (mV)

The +5 V REC and +12 V REC voltages are supplied for
the optional thermal recorder. The +5 V REC supply
voltage is generated in the recorder board by a step-
down converter from the + 12 V received from the DC/
DC board. The + 5 V REC and +12 V REC are measured
from the module frame flex board. These voltages are “-
-”, if recorder is not installed.

+15V MOD PSM voltage (mV)

The +15 V MOD PSM voltage is supplied for the PSM
module. The voltage is measured from the module
frame flex board.

«
...
150
151
152
153
154
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B650

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: Harken Страницы: 4

Бренд: VeEX Страницы: 2

Бренд: JB-Lighting Страницы: 48

Crouse-hinds series

Бренд: Eaton Страницы: 32

Бренд: Rane Страницы: 38

Бренд: Kartsana Страницы: 36

Бренд: Madrigal Страницы: 5

Бренд: MacDon Страницы: 504

Бренд: NanoVibronix Страницы: 2

Бренд: NanoVibronix Страницы: 32

Shapes Hexagons

Бренд: Nanoleaf Страницы: 27

Бренд: Tascam Страницы: 78

MINISTUDIO CREATOR US-42

Бренд: Tascam Страницы: 11

Бренд: Waterpik Страницы: 2

Бренд: Agilent Technologies Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды