GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 213 | Manualshive

Страница: 213 / 240

background image

Disassembly and reassembly

205

2062973-002

12.4.3 Replacing the User Interface Board

Disassemble first:
a.

12.3.3. Detaching the Frame Side Housing Decorations

b.

12.3.4. Detaching the Top Cover

c.

12.4.1. Detaching the Front Unit Assembly

12.4.4 Replacing the Trim Knob and Trim Knob Encoder

Disassemble first:
a.

12.3.3. Detaching the Frame Side Housing Decorations

b.

12.3.4. Detaching the Top Cover

c.

12.4.1. Detaching the Front Unit Assembly

1. Detach 2 screws and the PCB mounting parts.
2. Detach cables from User Interface Board:
- the Alarm Board cable
- the Trim Knob Encoder cable
- the Buzzer cable
- the touchscreen sensor (only in touchscreen

models)

3. Detach the User Interface Board.

•

Reassemble in reverse order.

NOTE: When reassembling align the UI board connector to the keypad connector.
NOTE: The User Interface Board FRU includes the UI cable. Preferably use the original UI cable if it seems to be
visually undamaged. In case you need to replace the UI cable, you need to additionally detach the rear unit
assembly to get access to the CPU board and be able to connect the inverter cable to the CPU board.
NOTE: After replacing the User Interface Board, during the first start-up, the patient monitor will automatically
check the UIC software version in the replaced user interface board and update the software if necessary.
Wait for 5 minutes to see if the software update is initiated and do not interrupt the process.

To replace the Trim Knob:
1. Pull the Trim Knob off from the front side.
2. Detach the nut and washer from the front side

using the 11 mm wrench. [1.6 Nm]

3. Detach the Trim Knob Encoder Cable from the

User Interface Board.

4. Detach the Encoder from the back of the

Front Unit.

•

Reassemble in reverse order.

NOTE: When reassembling, position the encoder as shown in the picture.

Trim Knob

encoder

Alarm

cable

Buzzer

Touch screen

cable

cable

board

UI cable

cable

«
...
211
212
213
214
215
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B650

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: Campden instruments Страницы: 8

Бренд: National Instruments Страницы: 16

Бренд: Jasco Страницы: 11

Бренд: Raytheon Страницы: 69

Бренд: Galaxy Audio Страницы: 24

Бренд: UFO Страницы: 16

Бренд: Abicor Binzel Страницы: 92

Бренд: Datavideo Страницы: 48

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 3

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 8

Бренд: Datavideo Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды