GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 235 | Manualshive

Страница: 235 / 240

background image

Verification procedure for wireless MC Network infrastructure

C- 3 (6)

2062973-002

Test setup

The patient monitors and the CIC Pro shall be installed, configured and tested to operate in the
same MC Network.

CIC Pro:

•

Configure the CIC to capture full disclosure data from the wireless CARESCAPE monitor.
Refer to CIC Pro Clinical Information Center Service Manual and CIC Pro Clinical
Information Center Operator's Manual for detailed instructions.

Wired CARESCAPE monitor, the stationary monitor

Setting up the connections:
1.

Connect a PDM or PSM module to the patient monitor.

2.

Connect the ECG cables to the module and to the patient simulator.

3.

Turn on the patient monitor and the patient simulator.

Configuring the patient simulator:
Refer to the simulator documentation for details on how to use and configure the simulator.
4.

Configure the patient simulator to output ECG waveform with:

−

ECG rhythm: a normal sinus rhythm

−

Heart rate: 80 bpm

−

Amplitude: 1 mV

Configuring the patient monitor:
5.

Select ECG1, ECG2 and ECG3 waveform fields to the screen with adequate priority.

6.

In the

Parameter Setup > ECG > Setup

, select:

−

ECG1 lead: II

−

ECG2 lead: V1

−

ECG3 lead: aVL

.

7.

Start a patient case / admit a patient in

Data & Pages > Admit/Discharge

menu.

Wireless CARESCAPE monitor, the transport monitor

NOTE: The PDM/PSM module, ECG cables and the patient simulator for the wireless CARESCAPE
monitor are needed only, if a CIC with full disclosure license is available in the MC Network. If
CIC with full disclosure license is not available, skip steps 2, 3, 4, 7 and 8.
NOTE: Ensure that the patient monitor battery, the service PC battery and the patient simulator
battery are fully charged.

Setting up the connections:
1.

Set up the CARESCAPE monitor and the service PC on a roll cart.

2.

Connect a PDM or PSM module to the patient monitor.

3.

Connect the ECG cables to the module and to the patient simulator.

4.

Connect the service PC to the patient monitor IX port using the Ethernet crossover cable.

5.

Turn on the patient monitor, the service PC and the patient simulator.

«
...
233
234
235
236
237
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B650

Бренд: Walker Bay Страницы: 8

Бренд: Labnet Страницы: 2

Бренд: Keithley Страницы: 42

Бренд: Above All Страницы: 4

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

DISHSTAR ADA-SEER

Бренд: Jackson Страницы: 2

Бренд: lancer Страницы: 3

Бренд: lancer Страницы: 12

Бренд: R2 Страницы: 26

Бренд: Gaspardo Страницы: 44

MiniLift160 Classic

Бренд: Handicare Страницы: 28

Бренд: Hands Free Farm Страницы: 24

Бренд: i-Optik Страницы: 75

Бренд: B-K lighting Страницы: 2

Бренд: Grundfos Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды