GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 240

background image

CARESCAPE Monitor B650

34

2062973-002

Alarm priority indicator: Low (cyan). Indicates a low priority alarm.

Alarm volume icon. Adjust the minimum alarm tone volume.

Audio alarms off indicator - Displays in the upper left corner of the alarm
area when physiological audible alarms are turned off.

Audio alarms paused indicator with countdown timer - Indicates all audio
alarms are paused and the amount of time remaining for the alarm pause
period displays as a countdown timer.
Displays in the upper left corner of the screen.

Pause audio alarms - Selectable from the monitor’s main menu. Also an
indicator of a temporarily paused active audio alarm.

Low priority audio off alarm indicator, Displays in the upper left corner of
the alarm area.

Only with software version 2 host build 2.0.7 or earlier:

Configuration warning. Displays when the priority setting for

HR/PR

high/low

, or

SpO2 low

has been set to low. Check the alarm

configuration. Displays in the upper left corner of the alarm area.

With software version 2 host build 2.0.7 or earlier:

General warning sign. Displays when the priority setting for

HR/PR

high/low

, or

SpO2 low

has been set to low.

Displays in the:

•

Lower part of the parameter menu’s

Alarms

tab

•

Priority column of the selected alarm in the

Alarm Setup

>

Alarm

Priorities

.

With software version 2 host build 2.0.8 or later:

General warning sign. Displays when the priority setting for

Tachy/Brady

PR high/low

or

HR/PR high/low

, or

SpO2 low

has been set to low, or when

the low priority volume is set to 0.
Displays in the:

•

Upper left corner of the screen

•

Lower part of the parameter menu’s

Alarms

tab

•

Priority column of the selected alarm in the

Alarm Setup

>

Alarm

Priorities

.

The following symbols appear in the software user interface

«
...
40
41
42
43
44
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B650

Бренд: GBC Страницы: 8

Бренд: KAPSCH Страницы: 57

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренд: Ecco Страницы: 17

PORTABLE ICE FISHING KIT

Бренд: Garmin Страницы: 5

Бренд: OHAUS Страницы: 84

Бренд: T&D Страницы: 28

Бренд: YASKAWA Страницы: 81

Бренд: YASKAWA Страницы: 52

Бренд: Masalta Страницы: 13

MT765 Challenger

Бренд: Fast Страницы: 31

Бренд: Jandy Страницы: 52

Fusionchef pearl

Бренд: Julabo Страницы: 43

KONTROL KUBE ABACUS

Бренд: FIBERLOCK Страницы: 8

Бренд: Monosem Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды