GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 240

background image

CARESCAPE Monitor B650

42

2062973-002

4.3 Local access to Webmin with a service PC connected

to the MC connector

You can access Webmin locally by connecting an Ethernet crossover cable between the
service PC and the MC connector of the patient monitor.
NOTE: This connection method is available only if the monitor is equipped with the Standard
Interface Board that provides only the MC connector and the patient monitor is in a discharged
state.
NOTE: Ensure that there is no patient admitted, prior to disconnecting the monitor from a live
MC or S/5 Network.
NOTE: Normal patient monitoring is disabled in this connection method. You must exit the
maintenance mode to re-enable the normal patient monitoring mode. (Refer to “

’ on page 43.)

1.

Connect a service PC to the MC

connector on the patient monitor using a crossover cable.

2.

Select

Monitor Setup > Service calibrations.

3.

Log in with your biomed username and password and press

Enter

.

4.

Record the

MC IP Address

shown next to the

Start

Maintenance Mode –menu button:

MC IP Address: ______________________

MC Netmask: ______________________

5.

Select

Start

Maintenance Mode.

A screen saver with the text “Note: Monitor temporarily under maintenance” appears on
the screen.

6.

Configure the service PC’s IP address and subnet mask to the same network segment
with the monitor’s MC Network.

NOTE: For more information on how to configure the IP address, refer to the PC’s
documentation.
7.

Launch a web browser on the service PC.

8.

In the

Address

field, type

https:

//

[MC IP address]:10000

and press

Enter

.

NOTE:

[MC IP address]

is the MC Network IP address of the patient monitor.

«
...
48
49
50
51
52
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B650

Бренд: Landoll Страницы: 52

Бренд: JBSYSTEMS Light Страницы: 14

Бренд: FagronLab Страницы: 16

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

Бренд: C.M.O Страницы: 10

Бренд: T-Rex Страницы: 13

The Wave Transformer

Бренд: EarthQuaker Devices Страницы: 21

Бренд: ParaBody Страницы: 3

Бренд: Valiani Страницы: 66

Бренд: Haas Страницы: 12

Бренд: SaMASZ Страницы: 25

Бренд: TC Electronic Страницы: 4

Бренд: TC Electronic Страницы: 6

Бренд: TC-Helicon Страницы: 12

Бренд: TC Electronic Страницы: 76

Бренд: Ultraflex Страницы: 48

Бренд: Valmar Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды