GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 240

GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 104

CARESCAPE Monitor B650

96

2062973-002

•

Contact GE Healthcare for any inquiries regarding the software CD and/or activation
code for the new host software version.

NOTE: Loss of monitoring - Software is activated only when the patient monitor is in a patient
discharged / case reset state. Normal patient monitoring is unavailable until the software
activation is completed. This may take up to 10 minutes.
NOTE: The existing clinical and platform settings of the patient monitor are saved and are not
affected by the activation of the new patient monitor software version. However, any new or
changed clinical and platform settings in the activated patient monitor software version have
their factory default values and may require manual configuration. For more information, refer
to the latest version of the CARESCAPE Modular Monitors Supplemental Information Manual.
Contact GE Healthcare for any inquiries regarding the software CD and/or activation code for
the new host software version.
1.

Log in to Webmin.

2.

Select

Configuration

>

Software Management

.

The

Software Management

window displays.

3.

In the

Software List

, select the software that you want to activate::

4.

Select

Next

.

The selected

Software activation

window appears.

5.

According to the software you are activating, proceed to:
•

Activating host software immediately

•

Activating host software after next case end / discharge

•

Activating module software

Software

Purpose of use

Host Software

Patient monitor software for the host unit including:

•

UIC SW for the UI board

•

EMBC SW for the CPU board

•

PMC SW for the DC/DC board

PDM Software

CARESCAPE Patient Data Module

PiCCO Software

E-PiCCO module.

sGAS Software

CARESCAPE respiratory modules, E-sCAiOV family.

«
...
102
103
104
105
106
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды