GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 240

GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 106

CARESCAPE Monitor B650

98

2062973-002

Software activation in progress. Do not disconnect any measurement modules or
other peripheral devices, or shut down the monitor until the software activation is
complete. Activation may take up to 10 minutes. The device will automatically restart
once the software activation is complete.

NOTE: When the software is activated first time after a uDOM replacement, the screen
saver does not appear.

7.

Wait until the software activation completes and the patient monitor restarts
automatically.

8.

Verify that the software activation is successful and the patient monitor runs the
activated software.

Activating host software after next case end / discharge

If you want to activate the new host software with a time delay, that is, after the next case end
/ patient discharge, follow this instruction. You can initiate the software activation process with
a delay during an active patient case.

1.

In the

Host Software

window, verify that the software that you activate is listed as

Inactive

in

Current Software State

.

2.

In

Software License

, if applicable, enter the

Activation Code

for the new software

version.

3.

In

Software Activation

, select

After next case end / discharge.

«
...
104
105
106
107
108
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды