GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 214 | Manualshive

Страница: 214 / 240

background image

CARESCAPE Monitor B650

206

2062973-002

12.4.5 Replacing the Keypad

1. Pull the Trim Knob off.
2. Tear the Keypad panel from the Front Unit,

starting from the upper left corner.

NOTE: Try to leave as little glue as possible to the
front frame cover. If any glue remains clean the
surface with water-diluted alcohol.
Assembling the keypad:
- Remove the release liner of the keypad.
- Place the hole at right end of the keypad to

the Trim Knob shaft. Then carefully guide the
lower edge against the cover edging.

3. Tear the membrane keypad from the Front

Unit and detach the keypad connector that
connects it to the User Interface Board.

Assembling:
- Clean the glue from the surface.
- Remove the release liner from the membrane

keypad.

- Connect the membrane keypad connector

first and direct the membrane into place.

- Pat the membrane keypad carefully to stick it

to the front cover.

- Assemble the Keypad.

«
...
212
213
214
215
216
...
»

Содержание CARESCAPE Monitor B650

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B650

Бренд: ABB Страницы: 14

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: FEAS Страницы: 72

Бренд: Bard Страницы: 36

Бренд: Bard Страницы: 2

Бренд: Bard Страницы: 30

Бренд: Bard Peripheral Vascular Страницы: 44

Бренд: MagCore Страницы: 80

Бренд: MagCore Страницы: 80

Бренд: Zero 88 Страницы: 12

Бренд: Zeiss Страницы: 119

Бренд: Zehnder Rittling Страницы: 32

Sonorex Super RK 31

Бренд: BANDELIN Страницы: 21

BTL7-A/E501-M Series

Бренд: Balluff Страницы: 194

Бренд: B.Pro Страницы: 48

Бренд: ABB Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды