GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 227

Страница: 227 / 240

Installation check form

A - 3 (4)

2062973-002

Module type

S/N

Observed result

Acceptance
criteria

PASS

N.A.

FAIL

Patient (source) leakage current tests, using a test body

Normal Condition (NC)

Polarity: NORMAL

≤

10 µA

Single Fault Condition (SFC)

Ground closed (normal)

≤

50 µA

Ground open (normal)

≤

50 µA

Ground closed (reverse)

≤

50 µA

Ground open (reverse)

≤

50 µA

Normal Condition (NC)

Polarity: Reserved

≤

10 µA

Patient (sink) leakage current tests

Polarity: NORMAL

≤

µA

Polarity: Reserved

≤

µA

Electrical Safety Test completion

Functional check

Observed result

Acceptance criteria

PASS

N.A.

FAIL

Start-up

Monitor starts up normally.

Display

: Picture quality

Text is readable, images are clear and
brightness is good.

Display

: Touchscreen control

Touchscreen is correctly calibrated
and operates correctly.

Device Information

Device information is correct.

Configuration Information

Monitor is correctly configured.

Keypad and remote

: Hard key

Selected menu opens and selected
activity starts.

Keypad and remote

: Trim Knob

Selected menu opens and selected
activity starts.

Mouse

Selected menu opens and selected
activity starts.

Alphanumeric keyboard

Keyboard language configuration is
correct.

Barcode reader

Data is correctly populated.

MC Network and S/5 Network

Network symbol and o

ther

monitor’s patient data is correctly
shown on the screen.

Wireless LAN

WLAN network symbol and o

ther

monitor’s patient data is correctly
shown on the screen.

Содержание CARESCAPE Monitor B650

















































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B650

Отзывы:

Похожие инструкции для CARESCAPE Monitor B650

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B650, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B650

Отзывы:

Похожие инструкции для CARESCAPE Monitor B650

Бренды по названию

Популярные бренды