GE HEALTHCARE CARESCAPE Monitor B650 Скачать руководство пользователя страница 161

Страница: 161 / 240

Troubleshooting

153

2062973-002

•

The LED is flashing to indicate Activity, i.e., the patient monitor is either transmitting or
receiving data packets over the network.

11.6 Battery diagnostics

You can check the monitor battery status from the

Battery Status

menu.

Select

Monitor Setup > Battery Status

The

Monitor Battery Status

menu will open.

Field

Status

Description

Time to empty
(hh:mm)

hh:mm

Estimated operating time before the battery is
empty.

N/A

Battery is not connected to the patient monitor
or battery is being charged.

Charge Level (%)

Battery charge level compared to full capacity
(in percentage).

N/A

Battery is not connected to the patient monitor.

Slot status

"No battery"

Battery is not connected to the patient monitor.

"No communication" Battery is connected to the patient monitor, but

battery communication failure error condition is
on.

"Failure"

Battery error condition is on.

"Discharging"

Patient monitor is operating on battery power.

"Charging"

Patient monitor is connected to AC mains and
charging the battery.

"Full"

Patient monitor is connected to AC mains and
battery is fully charged.

Time to full (hh:mm)

hh:mm

Estimated time to charge the battery to full
capacity.

N/A

Battery is not connected to the patient monitor
or battery is being discharged.

Temperature

"OK"

Battery temperature is ok.

"Over temperature"

Battery temperature error due to high battery
temperature.

"N/A"

Battery is not connected to the patient monitor.

Содержание CARESCAPE Monitor B650

















































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B650

Отзывы:

Похожие инструкции для CARESCAPE Monitor B650

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B650, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B650

Отзывы:

Похожие инструкции для CARESCAPE Monitor B650

Бренды по названию

Популярные бренды