49
AT+CPAS
Displays whether the
control signal to the FOMA
terminal is available or not.
Result: +CPAS: <pas>
pas:
0 : FOMA terminal can send/receive control
signal.
1 : FOMA terminal can not send/receive
control signal.
2 : Unknown (control signal sending/
receiving is not assured).
3 : FOMA terminal can send/receive control
signal and it is currently receiving.
4 : FOMA terminal can send/receive control
signal and it is currently communicating.
AT+CPAS
+CPAS:0
OK
AT+CPAS?
ERROR
AT+CPAS=?
+CPAS:(0-4)
AT+CPIN
Enters the PIN code in the
FOMA terminal.
Format: AT+CPIN=“<pin>”,“<newpin>”
This command is to enter the PIN1,
PIN2, or PUK code - depending on
the state of the result code returned
when AT+CPIN? is entered - of the
FOMA terminal.
Even if PIN code entry or the PUK
code is requested on the screen,
depending on the state of the result
code when AT+CPIN? is entered,
you may not be able to use this
command to enter the PIN. Do not
use this command to change PIN
code. Put <pin> and <newpin> in “ ”.
AT+CPIN? result
+CPIN
:
READY
:
PIN1 code, PIN2
code
Cannot enter the PUK1 or PUK2 code
+CPIN
:
SIM PIN
:
PIN1 entry standby
+CPIN
:
SIM PIN2
:
PIN2 entry standby
+CPIN
:
SIM PUK
:
PIN1 blocked
(Can enter PUK1 code)
+CPIN : SIM PUK2 : PIN2 blocked
(Can enter PUK2 code)
The command displayed on the right
is an entry sample of PIN code
“1234” and PUK code “12345678”.
(The status in which
+CPIN: READY is
answered when
+CPIN? is entered)
AT+CPIN=“1234”
ERROR
(The status in which
+CPIN: READY is
answered when
+CPIN? is entered)
AT+CPIN=“12345678”,
“1234”
ERROR
(The status in which
+CPIN: SIM PIN is
answered when
+CPIN? is entered)
AT+CPIN=“1234”
OK
(The status in which
+CPIN: SIM PUK is
answered when
+CPIN? is entered:
PIN1 lock status)
AT+CPIN=“12345678”,
“1234”
OK
(The status in which
+CPIN: SIM PUK2 is
answered when
+CPIN? is entered:
PIN2 lock status)
AT+CPIN=“12345678”,
“1234”
OK
AT+CPIN?
+CPIN:READY
OK
AT+CPIN=?
OK
AT+CR=
n
[&F] [&W]
When the line is connected,
displays the bearer service
type before the CONNECT
result code is displayed.
n
= 0 : Not display (initial value).
n
= 1 : Display.
<serv>
: Displays only “GPRS”, which means
packet communication.
(Displaying “SYNC”, “AV32K” or
“AV64K” depending on the line type.)
AT+CR?:
:
Displays the current setting.
AT+CR =1
OK
ATD
*
99
***
1#
+CR : GPRS
CONNECT
AT command
Outline
Parameter/description
Command execution example
Содержание N903i
Страница 208: ......
Страница 499: ...497 dIndex Quick Manual Index 498 Quick Manual 506 ...
Страница 576: ...Kuten Code List ...