Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 196

background image

Engine Operation

Regular Inspection

General Information

Engine oil lubricates, cools, seals, prevents corrosion, and cleans engines, enhancing engine
performance and extending the engine's lifetime. If the engine is continuously operated while
engine oil is insufficient the moving parts of the engine may get stuck, causing engine faults.

Engine oil should be checked with the oil level gauge and replenished if required. Oil level
should be checked while the engine is shut down. To check the oil level, shut down the engine
and wait for 5 ~ 10 minutes to allow the engine oil to flow back into the oil pan. The engine oil
level should indicate between the upper limit and the lower limit of the oil level gauge.

Engine oil should be periodically replaced based on the regular inspection table and the oil
filter and the cartridge should be replaced as the engine oil is replaced.

Engine Oil Standards

Use the specified engine oil suitable for the environment and conditions of the site where
the engine will be used.

Please use the engine oil which satisfies the following recommended specifications (See
Table 4-1).

TABLE 4-1: ENGINE OIL STANDARDS

Engine Model

SAE Classification

Oil Class

DL01/DL02

SAE 10W30

API CJ-4 or Better

DL01/DL02

SAE 15W40

API CJ-4 or Better

Note: Doosan engine oils are recommended for use in this machine. If Doosan engine oil
is not available, use a good quality engine oil that meets API service classification of CJ-4
or Better (See Table 4-1).

94

«
...
92
93
94
95
96
...
»

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P185WDOU-T4F (F89)

Бренд: ULTIMATE SPEED Страницы: 36

Бренд: ZIPPER MASCHINEN Страницы: 33

Бренд: KAESER KOMPRESSOREN Страницы: 304

Бренд: Ingersoll-Rand Страницы: 59

Бренд: Strend Pro Страницы: 64

Бренд: Black Ridge Страницы: 28

Quick Flow 2020

Бренд: Wagan Страницы: 20

Ninja Jet IS-35

Бренд: Iwata Страницы: 8

Бренд: Vector Страницы: 12

Бренд: Becker Страницы: 6

Бренд: Becker Страницы: 21

Бренд: Atlas Copco Страницы: 94

Бренд: Atlas Copco Страницы: 114

Бренд: Atlas Copco Страницы: 114

Бренд: Royce Страницы: 14

Бренд: California Air Tools Страницы: 17

Бренд: Mouvex Страницы: 16

Бренд: Superex Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды