Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 146

Страница: 146 / 196

Troubleshooting

Complaint

Cause

Correction

Ambient temperature above
rated ambient temperature
range.

Operate in cooler
environment.

Compressor tilted beyond
out-of-level operating limit.

Reposition or relocate
compressor to be more level.

Low compressor oil.

Add compressor oil. Look for
and repair any leaks.

Wrong compressor oil.

Change compressor oil.
Review compressor oil
specification.

Dirty cooler(s).

Clean exterior of cooler(s).

Dirty operating conditions.

Move compressor to cleaner
environment.

Clogged compressor oil
filter(s).

Replace compressor
oil filter(s) and change
compressor oil.

Clogged fuel filters.

Service fuel filters. See
Engine manual. Drain, clean
fuel tanks. Add clean fuel.

Operating pressure too high.

Reduce pressure to rated
operating pressure.

Recirculation of cooling air.

Close enclosure doors.
Close and secure access
panels. Check for loose or
missing belly pans.

Malfunctioning compressor
oil thermostat.

Replace thermostat element
in conventional bypass
valve, if equipped. Replace
valve.

No air flow.

Check electric fans to ensure
they are operating.

Malfunctioning minimum
pressure valve.

Repair or replace valve.

Blocked or restricted oil lines. Clean by flushing, or replace

lines.

Airend malfunctioning.

See Complaints #11, #12.

6. High Compressor Oil
Temperature

Loosen or broken belts.

Tighten or replace belt set.

146

Содержание P185WDOU-T4F (F89)





































































































































































































Результаты поиска

Содержание P185WDOU-T4F (F89)

Отзывы:

Похожие инструкции для P185WDOU-T4F (F89)

Бренды по названию

Популярные бренды

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание P185WDOU-T4F (F89)

Отзывы:

Похожие инструкции для P185WDOU-T4F (F89)

Бренды по названию

Популярные бренды