Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 144

Страница: 144 / 196

Troubleshooting

Complaint

Cause

Correction

Blown fuse.

Identify and replace fuse.
See Electronic Service
Manual.

Malfunctioning main power
switch.

Check switch. Replace if
necessary. See Electronic
Service Manual.

Clogged fuel filters.

Service fuel filters. See
Engine Manual.

Out of Fuel.

Add clean fuel.

Compressor oil temp. too
High.

See Complaint #6.

Engine coolant temp. too
High.

Check coolant level. If low,
add coolant. See Complaint
#3.

Engine oil pressure too Low.

See Complaint #4.

Loose wire connection.

Check wires at switches
and connectors to find loose
connection. Make repairs.
See Electronic Service
Manual.

Defective sensor.

Identify and check sensor.
Replace if necessary. See
Electronic Service Manual.

Malfunctioning relay.

Identify and check relay.
Replace if necessary. See
Electronic Service Manual

Engine malfunctioning.

See troubleshooting in
Engine manual.

Airend malfunctioning.

See Complaint #6.

2. Compressor won’t Start
or Run (continued)

Starter will not turn engine
over.

Check battery, check fuel.
Engine will not crank without
40 psi of fuel pressure.

Low coolant level.

Check coolant level. If low,
add coolant.

Loose or broken belts.

Tighten or replace belt set.

Ambient temperature above
rated ambient temperature
range

Operate in cooler
environment.

Dirty operating conditions.

Move compressor to cleaner
environment.

3. High Engine Coolant
Temperature

Dirty cooler(s).

Clean exterior of cooler(s).

144

Содержание P185WDOU-T4F (F89)





































































































































































































Результаты поиска

Содержание P185WDOU-T4F (F89)

Отзывы:

Бренды по названию

Популярные бренды

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание P185WDOU-T4F (F89)

Отзывы:

Бренды по названию

Популярные бренды