Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 196

background image

Noise Emission

Noise Emission

This Section Pertains Only To Compressors Distributed Within The United States.

Tampering With Noise Control System Prohibited.

Federal Law Prohibits the following Acts or the Causing Thereof:

(1) The removal or rendering inoperative by any persons, other than for purposes of
maintenance, repair, or replacement, of any device or element of design incorporated into
any new compressor for the purpose of noise control prior to its sale or delivery to the ultimate
purchaser or while it is in use; or (2) the use of the compressor after such device or element
of design has been removed or rendered inoperative by any person.

Among those acts included in the prohibition against tampering are these:

1. Removal or rendering inoperative any of the following:

A. The Engine Exhaust System or Parts thereof

B. The Air Intake System or Parts thereof

C. Enclosure or Parts thereof

2. Removal of any of the following:

A. Fan Shroud

B. Vibration Mounts

C. Sound Absorption Material

3. Operation of the Compressor with any of the Enclosure Doors Open.

Compressor Noise Emission Control Information

A. Removal or rendering inoperative, other than for the purpose of maintenance, repair,
or replacement of any noise control device or element of design incorporated into this
Compressor in compliance with the Noise Control Act.

B. The use of this Compressor after such device or element of design has been removed
or rendered inoperative.

Note: The Above Information Applies Only To Compressors That Are Built In
Compliance With The U.S. Environmental Protection Agency.

Portable power reserves the right to make changes or add improvements without notice
and without incurring any obligation to make such changes or add such improvements to
products sold previously.

The purchaser is urged to include the above provisions in any agreement for any resale
of this Compressor.

48

«
...
46
47
48
49
50
...
»

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P185WDOU-T4F (F89)

Бренд: ENKHO Страницы: 46

Бренд: stayer Страницы: 32

Yellow Profi Line 410-33

Бренд: Zgonc Страницы: 40

Craftsman 919.150270

Бренд: Craftsman Страницы: 11

Craftsman 919.153011

Бренд: Craftsman Страницы: 16

PERMANENTLY LUBRICATED TANK MOUNTED AIR COMPRESSOR 919.167321

Бренд: Craftsman Страницы: 44

evolv 921.167500

Бренд: Craftsman Страницы: 28

Бренд: Craftsman Страницы: 35

Бренд: Craftsman Страницы: 50

Бренд: Craftsman Страницы: 52

Бренд: Comprag Страницы: 100

Бренд: Air Mate Страницы: 68

Бренд: WilTec Страницы: 12

Бренд: WEISS Страницы: 36

Бренд: MULTIQUIP Страницы: 16

JEFCIND270L-10.0

Бренд: Jefferson Страницы: 13

Бренд: IMG STAGELINE Страницы: 26

EX-HG44e Series

Бренд: GEA Bock Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды