Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 143

Страница: 143 / 196

Troubleshooting

Troubleshooting Chart

Complaint

Cause

Correction

Out of Fuel.

Add Clean Fuel.

Compressor Oil Temp. too
High.

See Complaint #6.

Engine Coolant Temp. too
High.

Check Coolant level. If low,
add Coolant. See Complaint
#3.

Engine Oil Pressure too Low. See Complaint #4.

Loose or Broken Belts.

Tighten or replace belt set.

Loose wire connections.

Check wires at switches
and connectors to find loose
connection. Make repairs.
See Electronic Service
Manual.

Low fuel level fault.

If adequate fuel in the
tank, check fuel level
sender device. Replace
if determined faulty. See
Electronic Service Manual.

Defective sensor.

Identify and check sensor.
Replace if necessary. See
Electronic Service Manual.

Malfunctioning relay.

Identify and check relay.
Replace if necessary. See
Electronic Service Manual.

Blown fuse.

Identify and replace fuse.
See Electronic Service
Manual.

Engine malfunctioning.

See troubleshooting in
Engine manual.

1. Compressor has
stopped unexpectedly

Airend malfunctioning.

See Complaint #6.

Battery disconnect switch off. Check switch position and

operation.

Emergency stop pushed.

Check emergency stop
switch position and
operation.

2. Compressor won’t Start
or Run

Low battery voltage.

Check battery condition,
recharge if necessary.
Check electrolyte level, add
if necessary. Check cable
connections, clean and
tighten as needed.

143

Содержание P185WDOU-T4F (F89)





































































































































































































Результаты поиска

Содержание P185WDOU-T4F (F89)

Отзывы:

Бренды по названию

Популярные бренды

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание P185WDOU-T4F (F89)

Отзывы:

Бренды по названию

Популярные бренды