Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 196

background image

Lubrication

Some Oil Types Are Incompatible When Mixed And Result In The
Formation Of Varnishes, Shellacs, Or Lacquers Which May Be Insoluble.
Such Deposits Can Cause Serious Troubles Including Clogging Of The
Filters. Do Not Mix Oils Of Different Types And Avoid Mixing Different
Brands. A Type Or Brand Change Is Best Made At The Time Of A
Complete Oil Drain And Refill.

Portable Power Provides compressor Oil Specifically Formulated For
Portable compressors. Use Of These Fluids Is Required To Obtain
Extended Limited Airend Warranty.

These compressors are furnished with an initial supply of oil sufficient to allow operation until
the first service interval indicated in the

Maintenance Schedule

. If a compressor has been

drained of all oil, it must be refilled with new oil before it is placed in operation. Refer to
specifications in the Portable compressor Oil Chart.

If the compressor has been operated for the time/hours indicated in the

Maintenance

Schedule

, it should be drained of oil. If the compressor has been operated under adverse

conditions, or after long periods in storage, an earlier change may be necessary as oil
deteriorates with time as well as by operating conditions.

An oil change is good insurance against the accumulation of dirt, sludge, or oxidized oil
products.

Completely drain the separator tank, piping, and cooler. Note: if the compressor has been
operating under adverse conditions or has suffered long shutdown periods, more frequent
service intervals will be required. If the oil is drained immediately after the compressor has
been run for some time, most of the sediment will be in suspension and, therefore, will
drain more readily. However, the oil will be hot and care must be taken to avoid contact
with the skin or eyes.

After The compressor has been drained of all old oil, close the drain valves and/or plugs and
install new oil filter elements. Add oil in the specified quantity at the filler plug. Tighten the
filler plug and run the compressor to circulate the oil. Check the oil level. DO NOT OVERFILL.

117

«
...
115
116
117
118
119
...
»

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P185WDOU-T4F (F89)

Бренд: Fieldmann Страницы: 108

Бренд: Becker Страницы: 8

Бренд: DK2 Страницы: 52

SiloKing 1100 LS

Бренд: RTI Страницы: 14

Бренд: CARPOINT Страницы: 7

Бренд: California Air Tools Страницы: 16

Бренд: California Air Tools Страницы: 17

Бренд: MGF Страницы: 34

Бренд: WilTec Страницы: 8

Бренд: WEISS Страницы: 36

Бренд: Bauer Compressors Страницы: 43

Бренд: Bauer Compressors Страницы: 66

Бренд: Air-Zenith Страницы: 4

Бренд: Parkside Страницы: 44

Бренд: EINHELL Страницы: 44

Бренд: California Air Tools Страницы: 16

Бренд: Campbell Hausfeld Страницы: 40

Бренд: Campbell Hausfeld Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды