Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 196

background image

Maintenance

Fasteners

Visually check entire unit in regard to bolts, nuts and screws being properly secured. Spot
check several capscrews and nuts for proper torque. If any are found loose, a more thorough
inspection must be made. Take corrective action. (Refer to Torque Values Chapter in this
manual).

Running Gear/Wheels

Refer to the Preventive Maintenance Schedule in this manual for recommended servicing
intervals.

Check wheel nut torque 20 miles (30 kilometers) after refitting the wheels. Refer to Torque
Values later in this section.

Lifting jacks should only be used under the axle.

Bolts securing the running gear to the chassis should be checked for tightness. Re-tighten
where necessary. (Refer to Torque Values in this manual).

Lubrication

Always check the oil levels before a new compressor is put into service.

If, for any reason, the compressor oil has been drained, it must be re-filled with new oil
before putting into operation.

Engine Oil

Refer to the Preventive Maintenance Schedule in this manual for recommended servicing
intervals.

Fill engine with lubricating oil as specified in General Data Information section.

After the first 25 initial operating hours drain and replace engine oil.

The engine oil and oil filter element should be changed at the engine manufacturer's
recommended intervals. Refer to the Engine Operator Manual.

The Tier 4 engine in this compressor requires engine lubricating oil to ensure proper
Aftertreatment System operation and engine durability. Doosan Tier 4 Premium Engine Oil is
recommended. Refer to the Engine Operator Manual for engine oil specifications.

136

«
...
134
135
136
137
138
...
»

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P185WDOU-T4F (F89)

Бренд: STEELE PRODUCTS Страницы: 33

Бренд: Streetwize Страницы: 2

Бренд: EINHELL Страницы: 205

Бренд: Strend Pro Страницы: 64

Бренд: C-Aire Страницы: 17

Бренд: Sparmax Страницы: 2

Бренд: Kyocera Страницы: 132

Бренд: Copeland Страницы: 38

AA-98 AirPac II

Бренд: Aseptico Страницы: 8

Бренд: WilTec Страницы: 10

Бренд: New Holland Страницы: 52

Бренд: Sparmax Страницы: 32

Бренд: Sullivan-Palatek Страницы: 66

Бренд: Facom Страницы: 32

Бренд: Atlas Copco Страницы: 90

Бренд: Atlas Copco Страницы: 110

Бренд: NORAUTO Страницы: 54

Бренд: Campbell Hausfeld Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды