Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 196

Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 18

Safety Information

Compressor Description and Intended Use

This compressor is a mobile compressed air source. The Doosan compressor consists of
a trailer-mounted cabinet containing a fuel tank, diesel engine, compressor inlet system,
compressor cooling and lubrication system, compressor discharge system, control system,
instrument and electrical system. As the engine runs, the compressor converts mechanical
energy into air power.

When air is consumed by the compressor, the inlet unloader valve opens, and air is drawn
into the compressor through a dry type air filter. Air enters the housing of the compressor
where it is partially compressed. Air then passes along the flutes from the wide end to the
narrow end where it is compressed to the desired discharge pressure.

The oil is removed by air/oil separator filter. This oil is returned to the system to aid in
compressor lubrication.

Air passes through an air cooled aftercooler, where it is cooled. The flow and service
pressure for compressed air is controlled by the operator from the instrument/control panel.

Refer to the product specifications general data section in this manual for the output air
delivery and operating pressure of this compressor, and for the maximum output air power
limit of this compressor.

This compressor has been designed and built strictly for the intended use described above.
Using the compressor for any other purpose could permanently damage the compressor or
seriously injure the operator or other persons in the area. Compressor damage caused
by misuse is not covered under warranty.

The following are some examples of misuse:

•

Operating the compressor in a manner that is inconsistent with all federal, state
and local codes and regulations.

•

Using the compressor as a ladder, support, or work surface.

•

Using the compressor to carry or transport passengers or equipment.

•

Using the compressor to tow other compressors.

•

Operating the compressor outside of factory specifications.

•

Operating compressor in a manner inconsistent with all warnings found on the
compressor and in the Operator’s Manual.

18

«
...
16
17
18
19
20
...
»

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов