manualshive.com logo in svg

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 40

Lifting, Transporting and Preparation

Utility Package Set-Up (No Running Gear)

FIGURE 2-2: UTILITY PACKAGE SET-UP (NO RUNNING GEAR)

The unit must be secured while operating or transporting. The compressor must be located
on vehicle bed to allow access of normal servicing and maintenance.

See Figure X (See Figure 2-2) for mounting base holes provided in base. The compressor
should be hard mounted directly to the vehicle bed.

The air going into the inlet must be relatively free of oil, dirt, soot and other debris. It must be
no more than 10° F (5° C) over the ambient temperature.

The inlet and outlet grilles must not be restricted. See Figure Y (See Figure 2-2) for
recommended clearance around the compressor. The cross-sectional area of any ductwork
must be larger by a minimum of 10 percent.

Adjust raincap orientation and open away forward direction of truck.

The addition of any power-absorbing components (hydraulic pumps, paint mixers, etc.) must
be approved by Portable Power to maintain the warranty.

40

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды