Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 196

background image

Maintenance

Gauges

Instruments or gauges are essential for safety, maximum productivity and long service life
of the machine. Inspect the gauges and test any diagnostic lamps prior to start-up. During
operation observe the gauges and any lamps for proper functioning. Refer to Operating
Controls for the normal readings

Cooling Fan Drive

Every 3 months check to ensure fan drive mounting bolts to the engine have not loosened. If,
for any reason, it becomes necessary to remove or re-tighten the mounting bolts. Replace
bolts with Doosan approved bolts and torqued to 25 ft lbs. 35Nm.

The fan belt(s) should be checked monthly for wear and correct tensioning.

This compressor is equipped with a variable speed electric fan and requires no periodic
maintenance.

Fuel System

Refer to the Preventive Maintenance Schedule in this manual for recommended servicing
intervals.

The fuel tank(s) should be filled daily or every eight hours. To minimize condensation in the
fuel tank(s), it is advisable to top up after the compressor is shut down or at the end of each
working day. Drain any sediment or condensate that may have accumulated in the tank(s).

Diesel Exhaust Fluid

Refer to the Preventive Maintenance Schedule in this manual for recommended servicing
intervals.

Check the DEF level and add fluid as necessary. Use API certified DEF which meets ISO
22241. The DEF pump contains a filter that should be replaced at regular intervals.

Fuel Filter Water Separator

Refer to the Preventive Maintenance Schedule in this manual for recommended servicing
intervals.

The fuel filter water separator contains a filter element which should be replaced as required.

Charge Air Cooler Pipework

Foreign particles can damage the engine and turbocharger. Maintain internal cleanliness and
integrity of the air filtration, intake piping, and charge air cooler piping to help avoid damage.
Monthly inspect systems for leaks and that hoses, clamps, and connections are sealed.

133

«
...
131
132
133
134
135
...
»

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P185WDOU-T4F (F89)

Бренд: Gardner Denver Страницы: 84

Бренд: Prodif Страницы: 4

Бренд: Unimig Страницы: 12

Бренд: California Air Tools Страницы: 16

Бренд: Briggs & Stratton Страницы: 20

Vitrifrigo BD35

Бренд: Danfoss Страницы: 120

BrakeMaster 8310

Бренд: Roadmaster Страницы: 2

Бренд: Roadmaster Страницы: 2

Бренд: NORAUTO Страницы: 49

Бренд: EKOM Страницы: 78

Бренд: EKOM Страницы: 104

Бренд: EKOM Страницы: 108

Бренд: EKOM Страницы: 136

Бренд: Danfoss Страницы: 2

Бренд: Jet Страницы: 68

Бренд: Chicago Pneumatic Страницы: 28

Бренд: Chicago Pneumatic Страницы: 94

Бренд: Doss Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды