manualshive.com logo in svg

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 29

Safety

Air Hose Restraint Installation

Safety devices such as hose restraints (whipchecks) must be used to prevent hose whipping
if a connection fails. Whipchecks are to be constructed of woven stainless steel, galvanized
steel wire rope, or chain with a minimum strength adequate for the supplied pressure and
hose diameter. Whipchecks must be fastened to suitable mounting points or shackles.

The mounts and/or shackles are to be of the same or greater strength as the whipchecks.
An engineer should be consulted about suitability of whipchecks, mounts, mounting points,
shackles, and fittings as well as strength rating of materials. Whipchecks must be used at the
hose origination, termination, and each hose to hose connection.

Hoses can fail in areas other than at connecting points and require daily inspection of the
hoses for:

•

Cuts, Cracks, Or Kinks

•

Weakened Clamps Due To Rust And Corrosion

•

Damaged Connections

•

Deformity

•

Incorrect Or Incompatible Components Or Fittings

•

Any Visual Damage

Hoses must be selected that are rated for the application as to the maximum pressure and
temperature to be encountered as well as compatible with the materials being conveyed
inside the hose. Hoses must be compatible with the Compressor Oil.

Fuel Safety

For more information on fueling the compressor. Refer to Lifting, Transporting and
Preparation in this manual.

When fueling the compressor fuel tank:

•

Clean up any spilled fuel immediately.

•

Refill the fuel tank in a well-ventilated area.

•

Replace the fuel tank cap after refueling.

•

Do not smoke.

•

Do not refuel a hot or running engine.

•

Do not refuel the engine near sparks or open flames.

29

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды