manualshive.com logo in svg

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 20

Safety

Operating Safety

Familiarity and proper training are required for the safe operation of
the compressor. Compressor operated improperly or by untrained
personnel can be dangerous. Read the operating instructions contained
in both this manual and the engine manual and familiarize yourself with
the location and proper use of all controls. Inexperienced operators
should receive instruction from someone familiar with the compressor
before being allowed to operate it.

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down the compressor. They
also must meet the following qualifications:

•

Have received instruction on how to properly use the compressor.

•

Are familiar with required safety devices.

The compressor must not be accessed or operated by:

•

Children

•

People impaired by alcohol or drugs

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while operating this compressor:

•

Close-fitting work clothes that do not hinder movement.

•

Safety glasses with side shields.

•

Hearing protection.

•

Safety-toed footwear.

20

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды