Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 196

background image

Service Safety

A poorly maintained compressor can become a safety hazard! In order
for the compressor to operate safely and properly over a long period of
time, periodic maintenance and occasional repairs are necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or maintaining
this compressor:

•

Close-fitting work clothes that do not hinder movement.

•

Safety glasses with side shields.

•

Hearing protection.

•

Safety-toed footwear.

In addition, before servicing or maintaining the compressor:

•

Tie back long hair.

•

Remove all jewelry (including rings).

1. Do not perform even routine service (oil/filter changes, cleaning, etc.) until unit

is shut down.

Before servicing this compressor, make sure the engine start switch is turned to off
“O”, the negative terminal on battery is disconnected. Attach a “DO NOT START”
sign to the control panel. This will notify everyone that the unit is being serviced
and will reduce the chance of someone inadvertently trying to start the unit. If the
unit is connected to a remote start or transfer switch, make sure the remote switch
is also off and tagged.

2. Ground Connection

The compressor must be connected to a good earthen ground for proper operating
safety!

Ground the compressor in accordance with the standards defined in national, state,
and local regulations.

3. Do not attempt to open the reservoir cap while the unit is running or before the engine

has cooled down. Severe burns may result!

4. Do not allow water to accumulate around the base of the compressor. If water is

present, move the compressor and allow the compressor to dry before servicing.

5. Do not service the compressor if your clothing or skin is wet.

6. Do not allow untrained personnel to service this equipment.

22

«
...
20
21
22
23
24
...
»

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P185WDOU-T4F (F89)

Бренд: Briggs & Stratton Страницы: 52

Бренд: XPOtool Страницы: 8

BrakeMaster 8310

Бренд: Roadmaster Страницы: 2

Бренд: Roadmaster Страницы: 2

Бренд: Sparmax Страницы: 2

Бренд: Danfoss Страницы: 6

Performer SM 084

Бренд: Danfoss Страницы: 40

Maneurop MT R 22

Бренд: Danfoss Страницы: 56

Бренд: Schulz Страницы: 6

Бренд: STOCK-ade Страницы: 29

Бренд: AAVIX Страницы: 35

Бренд: Draper Страницы: 22

Бренд: Draper Страницы: 12

Бренд: CAMPAGNOLA Страницы: 4

Бренд: BSS Audio Страницы: 40

Бренд: AEG Страницы: 16

Бренд: Metasys Страницы: 24

Бренд: Danfoss Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды