Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 42

Страница: 42 / 196

Lifting, Transporting and Preparation

Fueling (Refueling) the Fuel Tank

Do not permit smoking, open flame, or sparks to occur near the battery,
fuel leaking solvents, or other flammable substances and explosive
gases.

Fire hazard. Fuel and its vapors are extremely flammable. Burning fuel
can cause severe burns.

•

Keep all sources of ignition away from the compressor while
refueling.

•

Refuel only when the compressor is outdoors.

•

Clean up spilled fuel immediately.

Flammable Fuels - Do not fill tank when engine is running.

Do not smoke or use an open flame in the vicinity of the compressor
or fuel tank.

Do not permit smoking, open flame, or sparks to occur near the battery,
fuel, cleaning solvents or other flammable substances and explosive
gases.

Diesel fuel and its vapors are dangerous to your health and the
surrounding environment. Avoid skin contact and/or inhaling fumes.

Requirements

Before fueling (refueling) the fuel tank, perform the following steps:

•

Compressor and fuel tank level with the ground.

•

Fresh, clean fuel supply.

Содержание P185WDOU-T4F (F89)





































































































































































































Результаты поиска

Содержание P185WDOU-T4F (F89)

Отзывы:

Похожие инструкции для P185WDOU-T4F (F89)

Бренды по названию

Популярные бренды

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание P185WDOU-T4F (F89)

Отзывы:

Похожие инструкции для P185WDOU-T4F (F89)

Бренды по названию

Популярные бренды