manualshive.com logo in svg

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 21

Safety

Only trained personnel are permitted to start, operate, and shut down the compressor. They
also must meet the following guidelines below for operating the compressor safety:

1. Do not operate the compressor when open containers of fuel, paint, or other

flammable liquids are near.

2. Do not place flammable material or liquids near the compressor.

3. Do not operate the compressor, or tools attached to the compressor, with wet hands.

4. Do not operate the compressor indoors unless exhaust fumes can be adequately

ventilated.

5. Do not overload the compressor. The total amperage of the tools and equipment

attached to the compressor must not exceed the load rating of the compressor.

6. Do not allow untrained personnel to operate or service the compressor.

7. Do not operate compressor in standing water.

8. Do not touch the hot engine, exhaust, or compressor components. Burns will result.

9. Do not start a compressor in need of repair.

10. Do not restart the engine until the cause of the trouble has been determined and fixed.

11. Wear hearing protection when operating equipment.

12. Follow starting and stopping instructions described in this manual. Know how to

operate and stop compressor before starting it.

13. Make a walk-around inspection of the compressor set before starting it. Open side

doors and visually inspect engine compartment for obvious damage or the presence
of foreign objects which might affect operation.

14. Keep the compressor at least one meter (three feet) away from structures, buildings,

and other equipment during use.

15. Store the compressor properly when it is not being used. The compressor should be

stored in a clean, dry location out of the reach of children.

16. Keep the area immediately surrounding and underneath the compressor clean, neat,

and free of debris and combustible materials. Make sure that the area overhead is
clear of debris that could fall onto or into the compressor or exhaust compartment.

17. Make sure the compressor is on a firm, level surface and will not tip, roll, slide,

or fall while operating.

18. Remove all tools, cords, and other loose items from the compressor before starting it.

19. Make sure the compressor is well-grounded and securely fastened to a good earthen

ground per national and local regulations.

21

Содержание P185WDOU-T4F (F89)





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды