Doosan P185WDOU-T4F (F89) Скачать руководство пользователя страница 153

Страница: 153 / 196

Compressor Diagnostic Codes

LCD Display

Display Name

Description

Type

CPR CODE 26
LOAD INHIBIT
DELAY

Load Inhibit Delay

The operator has attempted to load the
machine before the warm up timer has
expired.

ALERT

CPR CODE 28

Incorrect Engine ECU
Calibration

Engine ECU has a different calibration
than what is expected (Engine will not
crank).

ALERT

CPR CODE
29 ENGINE
SHUTDOWN
UNKNOWN

Engine Shutdown
Unknown

Engine stopped without an engine
diagnostic code.

FAULT

CPR CODE 30
HIGH AIREND
TEMP

High Airend
Discharge
Temperature

Airend discharge temperature greater
than or equal to 251° F.

FAULT

CPR CODE 32
AIREND DISC
TEMP SENSOR

Airend Discharge
Temperature Sensor

Airend discharge temperature sensor
reading out of range.

FAULT

CPR CODE
33 SEP TANK
PRES SENSOR

Separator Tank
Pressure Sensor

Separator Tank Pressure Sensor reading
out of range.

FAULT

CPR CODE 34
HIGH PRES AT
START

High Separator Tank
Pressure At Start

Separator Tank Pressure greater than 20
psi at crank attempt.

FAULT

CPR CODE 35
HIGH SEPT
TANK PRES

High Separator Tank
Pressure

Air Pressure in the Separator Tank
exceeded limit.

FAULT

CPR CODE 36
SAFETY VALVE
OPEN

Safety Valve Open

Safety relief valve on separator tank
opened.

FAULT

CPR CODE 38
AIR FILTERS
RESTRICTED

Intake Air Filters
Restricted

Intake filters restricting air flow.

ALERT

CPR CODE 39
LOW SYSTEM
VOLTAGE

Low System
Voltage/Alternator
Not Charging

Electrical system voltage below 13.5
VDC.

ALERT

CPR CODE 42
FUEL LEVEL
SENSOR

Fuel Level Sensor

Fuel Level Sensor reading out of range.

ALERT

CPR CODE 43
LOW SEP TANK
PRES

Low Separator Tank
Pressure

Separator tank pressure below 40 psi
after compressor is loaded.

FAULT

153

Содержание P185WDOU-T4F (F89)





































































































































































































Результаты поиска

Содержание P185WDOU-T4F (F89)

Отзывы:

Бренды по названию

Популярные бренды

Doosan P185WDOU-T4F (F89), Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание P185WDOU-T4F (F89)

Отзывы:

Бренды по названию

Популярные бренды