Canon iR3570 Series, Руководство по обслуживанию

Страница: 606 / 722

Chapter 15
15-18
# 037
There is a shortage of memory, not permitting reception. Remove error files and unnecessary files to increase
available memory.
# 080
F code is not set on the target. Check the F code of the target, and start over.
# 081
The appropriate password is not set on the target. Check the password of the target, and start over.
# 099
The transmission has been suspended in the middle. Start over.
# 102
There is a mismatch of F code or password. Check the F code and the password of the target, and
start over.
# 107
There is a shortage of memory, not permitting
transmission. 1. Decrease the resolution, and try once again.
2. Remove unnecessary files to increase available space.
# 701
The group ID set when the job was introduced no longer
exits. Or, the password has been changed. Type in the correct group ID or the ID No. (using the
keypad); then, start over.
# 702
The memory is full, not permitting transmission. 1. Wait a while. Try again until the ongoing transmission
of a job ends.
2. Try not to transmit to too many addresses at once;
rather, try dividing the address into smaller groups.
# 703
The memory image area is full, not permitting further
writing. 1. Wait a while. Try transmitting after the ongoing
transmission of a job ends.
2. Remove files from the Box; if the operation still fails
to return to normal, turn off and then back on the main
power.
# 704
An error has occurred while an attempt is made to obtain
address information from the address book. Check the settings of the address, and try once again; if
the operation is still not normal, try turning off and then
back on the main power.
# 705
The image data size is in excess of the upper limit
imposed on transmission data size set in user mode, thus
causing suspension of transmission. Try changing the upper limit imposed on transmission
data size as part of the communication control settings of
system control settings (user mode). When selecting low
resolution mode or using i-fax, try decreasing the
number of images to send at one time so that the
transmission will not be in excess of the upper limit
imposed on transfer data size.
# 706
An address table is being imported from or to the remote
UI; or, a different transmission component is being used. Start over once again.
# 711
All memory of the Box is used. Delete files from the Box.
# 712
The Box is full of files. Remove file from the Box.
# 713
The file has been removed from the Box before
transmitting the URL. Put the file in question back into the Box, and start over.
# 751
The server is yet to start up. The network is
disconnected. (The connection to the target may have
failed, or the connection may have been cut in the
middle.) Check the target. Check the network.
# 752
The SMTP server name of the e-main/i-fax in question
may be wrong, or the server in question is yet to start up.
Or, the appropriate domain name or e-mail address has
not been set. Or, the network has been disconnected. Using the network settings of the system control setup
(user mode), check the SMTP server name, domain
name, and e-mail address. Check to see that the SMTP
server is operating normally. Check the connection of
the network.
# 753
A TCP/IP error has occurred in the course of e-mail
transmission. (e.g., socket, select error) Check the condition of the network cable and the
connector. If the operation does not return to normal, try
turning off and then back on the main power of the
machine.
# 754
The server has not been started up for transmission, or
the network is disconnected. Or, the target settings are
wrong. Check the server and the network. Check the settings of
the target.
# 755
The TCP/IP settings are not operating normally, thus not
permitting transmission. In user mode, check the TCP/IP settings.
The appropriate IP address has not been set up. In user mode, check the TCP/IP settings.
Cause Remedy