Canon iR3570 Series, Руководство по обслуживанию

Страница: 517 / 722

Chapter 13
13-5
1) Connect the power plug to the power outlet, and turn on the main power
unit.
2) In the host machine's service mode, make the following selections:
COPIER>FUNCTION>DPC>D-GAMMA.
3) Press the OK key.
- The machine will pick up paper from cassette 1 (regardless of the size of
the paper inside the cassette).
- If no paper exists in cassette 1, the machine will try to find paper in the
lower cassettes in order.
- The paper will be discharged blank to end APVC correction.
4) Press the Reset key twice to end service mode.
13.5 Electrical Components
13.5.1 After Replacing the HDD
0007-8275
iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N /
/ iR4570N / iR2230 / / / iR3530 /
1) Format the HDD.
Start up the machine in safe mode (i.e., while holding down the 2 and 8 keys,
turn on the main power).
Using the HD format function of the SST, format all partitions ($); for
details, see the descriptions given for upgrading.
2) Download the system software.
Using the SST, download the following: LANGUAGE, RUI, PS-FRONT,
OCR dictionary, SSL coding key, SSL CA certificate, MEAP content.
Keep in mind that the machine may take about 5 min to start up after
downloading.
13.5.2 After Replacing the DC Controller PCB
0007-4922
iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N /
/ iR4570N / iR2230 / / / iR3530
- Before replacing the DC controller PCB, print out the latest P-PRINT page.
Å@Å@Å@ COPIER>FUNCTION>MISC-P>P-PRINT
1) Using the SST, download the latest system software.
2) Using the following service mode item, initialize the memory of the DC
controller PCB:
Å@ COPIER>FUNCTION>CLEAR>DC-CON
3) Using the following service mode items, enter the values indicated on the
P-PRINT page:
- COPIER>ADJUST>LASER> LA-DELAY/ LA-OFF/ POWER
- COPIER>ADJUST>DEVELOP> DE-OFST
- COPIER>ADJUST>BLANK> BLANK-T/BLANK-B
- COPIER>ADJUST>HV-RPRI> OFST-DC/ OFST-AC
- COPIER>ADJUST>HV-TR all items under
- COPIER>ADJUST>FEED-ADJ all items under
- COPIER>ADJUST>CST-ADJ all items under
- COPIER>ADJUST>FIXING all items under
- COPIER>ADJUST>MISC all items under
4) Execute the following service mode items:
- COPIER > FUNCTION > DPC > D-GAMMA
13.5.3 After Replacing the Main Controller PCB
0007-5188
iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N /
/ iR4570N / iR2230 / / / iR3530
If you are replacing the main controller PCB, be sure to transfer the
following components from the old to new PCB:
[1]Å@boot ROM
[2]Å@HDD
[3]Å@image memory (SDRAM)
[4]Å@counter memory PCB
F-13-22
If the user uses NetSpot Accountant (NSA) in Combination with a Card
Reader
The SDRAM of the main controller retains card ID used by NSA. If you have
replaced the main controller, you will have to download the card data from
NSA once again to permit NSA to perform statistical operations.
If you have formatted the HDD and downloaded the system software, you
will have to go through a specific set of steps:
1) Format the HDD.
2) Download the system software.
3) Make the following selections:
Å@COPIER>FUNCTION>INSTALL>CARD.
4) Enter a card No.
Å@Enter the first of the numbers that will be used for group control, and
press the OK key (e.g., if you are planning to use cards from No. 1 thorough
No. 100, enter '1').
5) turn off and then on the main power.
6) Check the count control mechanism in user mode.
Å@system control setup>group ID control>count control
check to see as many as 'ID00000001 through ID00001000' have been pre-
pared.
7) Set the IP address in user mode.
Å@system control setup>network setup>TCP/IP setup>IP address
Set 'IP address', 'gateway address', and 'sub net mask'.
8) Enter a number of your choice in user mode.
Å@system administrator info setup>system control group ID>system con-
trol ID No.
9) Hold down the control panel power switch for 3 sec or more.
10) Go through the instructions on the control panel for shut-down sequence
so that the main power switch may be turned off.
11) Turn off the main power switch. Wait for 3 sec or more, and turn it back
on.
Unless you have registered 'system control group ID' and 'system control
ID No.', you will not be able to register cards for the device in the course of
Net Spot Accountant setup work.
12) Download the card ID.
Å@Keep the machine in a standby state < and download the card ID to be
used from the NSA>
13) Check the count control particulars in user mode.
Å@system control setup>group ID control>count control
See that only the downloaded ID data is shown.
14) Check to see that the operation is normal.
Make copies using a user card that has been registered using the NSA, and
check to see that the count of the card in question has been incremented cor-
rectly.
13.5.4 After Replacing the Reader Controller PCB
0007-9843
iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N /
/ iR4570N / iR2230 / / / iR3530 /
- Before replacing the reader controller PCB, be sure to print out the lat-
est P-PRINT page.
<if you are executing RAM initialization for the reader controller without
replacing the PCB>
- Using the SST, upload the backup data of the reader controller, and down-
load it after initializing the RAM so that you need not perform the following:
1. Reader Unit-Related Adjustments
1) Using the SST, download the latest system software (R-CON).
2) Make the following selections in service mode: COPIER>FUNC-
TION>LEARN>R-CON. Then, press the OK key to initialize the RAM;
thereafter, turn off and then on the main power.
3) Enter the following values in service mode:
a. values indicated on the service label (found behind the left cover of the
reader unit)
a-1. CIS read position adjustment (for fixed reading)
COPIER>ADJUST>ADJ-XY>ADJ-X
a-2. main scanning direction position adjustment (for fixed reading)